Posted on

Case Crawler Excavator CX330 Factory Service & Shop Manual


Download Link

INSTANT DOWNLOAD (add to cart)


DIGITAL CAMERA

1,100+ pages, bookmarked, Searchable, Printable, high quality PDF
7-88631 – 24 Valve, 8.3 Liter Engine Service Manual.pdf – 496 pages
87565293 NA – Crawler Excavator CX330 Tier III Service Manual.pdf – 672 pages

Complete workshop & service manual with electrical wiring diagrams for Case Crawler Excavator CX330. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Case Crawler Excavator CX330 service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

EXCERPT:
TABLE OF CONTENTS
1 GENERAL INFORMATION
Safety, general information and standard torque data ..1001 7-27691NA
General specifications and special torque setting..1002 9-94170NA
Numerical value conversion table ..1003 9-35540
2 ENGINE
Radiator and engine, removal and installation ..2001 9-94830NA
Engine specifications .. *
Disassembly and assembly of the engine.. *
3 FUEL SYSTEM
Fuel tank ..3001 9-43471NA
Fuel engine system.. *
4 ELECTRICAL SYSTEM
Electrical system, electrical and electronic troubleshooting..4001 9-94180NA
Inspection and maintenance of batteries and connecting a booster battery..4002 9-43460NA
Main and engine electronic control boxes..4003 9-43451NA
5 UNDERCARRIAGE
Removal and installation of tracks ..5001 9-42910NA
Rollers..5003 9-42921NA
Sprocket ..5004 9-36890NA
Idler wheel and tension shock absorber ..5005 9-94790NA
6 DRIVE TRAIN
Drive motor and final drive transmission removal and installation ..6001 9-43141NA
Swing reduction gear, removal and installation..6003 9-43210NA
Swing reduction gear, disassembly and assembly..6004 9-43221NA
Travel reduction gear disassembly and assembly ..6005 9-43151NA
7 UNDERCARRIAGE HYDRAULICS
8 UPPERSTRUCTURE HYDRAULICS
Depressurising and decontaminating the hydraulic system, use of the
vacuum pump and bleeding the components ..8000 9-43501NA
Specifications, troubleshooting, checks and hydraulic pressure settings..8001 9-94190NA
Hydraulic reservoir removal and installation ..8002 9-43230NA
Main and pilot pumps, removal and installation ..8003 9-94840NA
Main hydraulic control valve, removal and installation ..8004 9-43261NA
Attachment cylinders, removal and installation ..8005 9-43251NA
Hydraulic swivel, removal and installation..8006 9-43390NA
Pilot blocs, removal and installation ..8007 9-43400NA
Swing motor, removal and installation..8008 9-43200NA
Main hydraulic pump, disassembly and assembly ..8010 9-94850NA
Main hydraulic control valve, disassembly and assembly ..8011 9-43551NA
Attachment cylinders, disassembly and assembly ..8012 9-94760NA
Hand control levers, disassembly and assembly ..8013 9-94630NA
Foot control levers, disassembly and assembly ..8014 7-28301NA
Six-solenoid valves, disassembly and assembly..8015 9-43361NA
Caution valve, disassembly and assembly..8016 9-94770NA
Hydraulic swivel, disassembly and assembly..8018 9-43190NA
Swing motor, disassembly and assembly ..8019 9-43441NA
Hydraulic functions..8020 9-94200NA
Travel hydraulic motor, disassembly and assembly..8021 9-43161NA
Hydraulic component functions..8030 9-94210NA
9 UPPERSTRUCTURE
Upperstructure, turntable and counterweight..9002 9-43411NA
Boom, dipper and bucket ..9003 9-43421NA
Seat and seat belt ..9004 9-40960NA
Cab and cab equipment..9005 9-94800NA
Air conditioning troubleshooting..9006 7-xxxxxFR
Air conditioning unit disassembly and assembly..9007 9-94640NA
Air conditioning servicing ..9008 7-xxxxxFR
Air conditioning components..9009 7-xxxxxFR
Large format hydraulic schematic ..Pocket 9-94040
Large format electrical schematic ..Pocket 9-94050
..
INSPECTING THE BATTERY
NOTE: For a proper inspection of the battery, carry out each part of the inspection until the actual state of the battery is known.
Visual inspection
– Check that the cable connections are clean and tightened properly. Remove all foreign bodies from the top of the battery.
– Check the box, the terminals and the battery cables for damage.
– Check the electrolyte level, see page 4.
– If you have added water to the battery, charge the battery for 15 minutes at 15 to 25 amperes to allow the water to mix correctly with the electrolyte.
Check the specific gravity
Use a battery hydrometer to check the specific gravity of the electrolyte. The specific gravity indicates the charge level in each cell.
Battery hydrometers are designed to indicate the correct specific gravity when the electrolyte is at a temperature of 26.7°C.
Before checking the specific gravity, check the electrolyte temperature. If the hydrometer is not equipped with a thermometer, use a thermometer to measure the electrolyte temperature. The thermometer has to be calibrated at least up to 52°C.
1. Remove sufficient electrolyte from a cell so that the float moves freely in the tube.
NOTE: If it is not possible to check the specific gravity without first adding water to the cell, charge the battery for 15 minutes at 15 to 25 amperes to allow the water to mix correctly with the electrolyte. Then, check the specific gravity.
2. Read the float.
3. Read the thermometer, if the reading is greater than 26.7°C, add specific gravity points to the reading to get the specific gravity. If the reading is less than 26.7°C, deduct specific gravity points from the reading to get the specific gravity. See the illustration below and add or deduct specific gravity points depending on the situation.
4. Record the corrected specific gravity for each cell.
5. If the difference between the high and low readings is 0.050 minimum, charge the battery and check the specific gravity again. If after charging the difference is still 0.050 minimum, install a new battery.
NOTE: When the battery is replaced, do not use a used battery with a new one. The life of the new battery will be reduced.
..