Posted on

Mitsubishi Colt 2004-2011 Factory Service & Shop Manual


Download Link

INSTANT DOWNLOAD (add to cart)



Mitsubishi Colt 2004-2011 Factory Service & Shop Manual
Complete workshop & service manual with electrical wiring diagrams for Mitsubishi Colt 2004-2011. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Mitsubishi Colt 2004-2011 service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

EXCERPT:
11B_Engine_Mechanical_(135).pdf
11A_Engine_Mechanical_(134).pdf
42_Body.pdf
00_General.pdf
13A_Multipoint_Fuel_Injection.pdf
35C_Traction_Control,_Active_Stability_Control_System.pdf
12_Engine_Lubrication.pdf
54A_Chassis_Electrical.pdf
52B_Suplemental_Restraint_System_(SRS).pdf
52A_Interior.pdf
37A_Power_Steering.pdf
54C_Controller_Area_Network_(CAN).pdf
55_Heater,_Air_Conditioner_and_Ventilation.pdf
35A_Servise_Brakes.pdf
37_Power_Steering.pdf
54B_Local_Interconect_Network_(LIN).pdf
35B_Four-Wheel_Anti-Skid_Brake_System_(4ABS).pdf
51_Exterior.pdf
22B_Automated_Manual_Transmission.pdf
13C_Fuel_Supply.pdf
15_Intake_and_Exhaust.pdf
14_Engine_Cooling.pdf
33A_Front_Suspension.pdf
21_Clutch.pdf
22A_Manual_Transmission.pdf
33_Front_Suspension.pdf
16_Engine_Electrical.pdf
32_Power_Plant_Mount.pdf
13B_Fuel_Supply.pdf
26_Front_Axle.pdf
17_Engine_and_Enmission_Control.pdf
34_Rear_Suspension.pdf
31_Wheel_and_Tyre.pdf
36_Parking_Brake.pdf
27_Rear_Axle.pdf
52_Interior_and_Suplemental_System.pdf
54_Chassis_Electrical.pdf
35_Service_Brakes.pdf
22_Manual_Transmission.pdf
11_Engine.pdf
13_Fuel.pdf
BRM_Colt_Z3_(ZM)

AIR BAG MODULE AND SEAT BELT PRE-TENSIONER DISPOSAL PROCEDURES
Before disposing of an air bag or a vehicle equipped with an air bag, follow the procedures below to deploy the air bag.
UNDERPLAYED AIR BAG MODULE DISPOSAL WARNING
• If the vehicle is to be scrapped or otherwise disposed of, deploy the air bags and operate the seat belt pre-tensioner inside the vehicle. If the vehicle will continue to be used and only the air bag modules and seat belt pre-tensioner are to be disposed of, deploy the air bags and operate the seat belt pre-tensioner outside the vehicle.
• Since a large amount of smoke is produced when the air bag is deployed and the seat belt pre-tensioner is operated, avoid residential areas whenever possible.
• Since there is loud noise when the air bags are deployed and when the seat belt pre-tensioner are operated, avoid residential areas whenever possible. If anyone is nearby, give warning of the impending noise.
• Suitable ear protection should be worn by personnel performing these procedures or by people in the immediate area.
DEPLOYMENT INSIDE THE VEHICLE (WHEN DISPOSING OF A VEHICLE)

1. Move the vehicle to an isolated spot.
DANGER
Wait at least 60 seconds after the disconnection of the battery cable before any further job (Refer to P.52B-5).
2. Disconnect the negative and positive battery cables from the battery terminals, and then remove the battery from the vehicle.