Author: admin

Service Manual (116 Hydraulic Excavator) 6570484 (4-87)

Complete workshop & service manual with electrical wiring diagrams for Bobcat 116 Hydraulic Excavator. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Bobcat 116 Hydraulic Excavator service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

Operator’s Manual (116 Hydraulic Excavator) 6570362 (4-88).pdf
Operator’s Manual (116 Hydraulic Excavator) 6570790 (4-88).pdf
Service Manual (116 Hydraulic Excavator) 6570484 (4-87).pdf

EXCERPT:
CONTENTS
10 ENGINE
12 TESTING AND ADJUSTING
1 3 DISASSEMBLY AND ASSEMBLY
20 POWER TRAIN
21 STRUCTURE AND FUNCTION
23 DISASSEMBLY AND ASSEMBLY
24 MAINTENANCE STANDARD
30 UNDERCARRIAGE
31 STRCTURE AND FUNCTION
33 DISASSEMBLY AND ASSEMBLY
34 MAINTENANCE STANDARD
60 HYDRAULIC SYSTEM
61 STRUCTURE AND FUNCTION
62 TESTING AND ADJUSTING
63 DISASSEMBLY AND ASSEMBLY
64 MAINTENANCE STANDARD
70 WORK EQUIPMENT
71 STRUCTURE AND FUNCTION
73 DISASSEMBLY AND ASSEMBLY
7 4 MAINTENANCE STANDARD
80 ELECTRICAL SYSTEM
81 STRUCTURE AND FUNCTION
…
TESTING TRAVEL OF CONTROL VALVE SPOOL
Put a steel tape in contact with control valve spool (1) to be tested and measure the distance the spool moves when the lever is operated.
* When measuring with one worker, pull the control lever with a string, or disconnect the rod at the spool end and move the spool directly to measure.
[Reference]
When results of test show that spool stroke is not within standard value:
Remove cover (2) of the spool and check if bolt (3) is loose. If there is no abnormality, disassemble the control valve and test.
…

BMW Z8 2000-2003

Complete digital official shop manual contains service, maintenance, and troubleshooting information for the BMW Z8 2000-2003. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual for BMW Z8 2000-2003 is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

EXCERPT:
2000-2003 ENGINE Engine Mechanical – Repair Instructions – Z8
CONNECTING ROD WITH BEARINGS
11 24 571 REPLACING ALL CONROD BEARINGS (S62)
(piston removed)
Install new conrod bearing shells.
Insert one blue (1) and one red (2) bearing shell for each conrod.
Fig. 413: Installing New Conrod Bearing Shells
Install pistons, refer to 11 25 530 REMOVING AND INSTALLING/REPLACING ALL PISTONS (S62) .
Check connecting-rod bearing clearance:
Fig. 414: Checking Conrod Bearing Clearance
Piston in BDC position.
Fit special tool 00 2 590 (Plastigage Type PG 1) to the oil-free crankshaft.
Place bearing caps in position, making sure that matching numbers are paired.
Use the old connecting-rod bolts to check connecting-rod clearance.
Tighten down conrod bolts with special tool 00 9 120.
Fig. 415: Tightening Conrod Bolts
Tightening Torque 11 24 1AZ, refer to 11 24 CONNECTING RODS AND BEARINGS .
Remove bearing cover and read off bearing clearance across width of pinched plastic thread with the help of the measuring scale.
Fig. 416: Checking Connecting-Rod Clearance
Conrod bearing clearance, refer to 11 21 CRANKSHAFT AND BEARINGS S62 .

Remove plastic thread.

Lubricate crankshaft and bearing shells.

Insert new conrod bolts and tighten down.
Tightening Torque 11 24 1AZ, refer to 11 24 CONNECTING RODS AND BEARINGS .
PISTON WITH RINGS
11 25 530 REMOVING AND INSTALLING/REPLACING ALL PISTONS (S62)
Special tools required:
 00 1 450
 00 9 120
 11 3 480
 11 7 180
(engine removed)
Removal
Removal of pistons is described separately from installation. Assembly sequence for removal and installation is
different.
Mount engine on special tool 00 1 450 and remove both cylinder heads. Refer to 11 12 517 Removing and installing both cylinder heads (S62) .
Remove lower oil sump section.
Remove oil circuit changeover valve on left and right. Refer to 11 13 540 Removing and installing/replacing
left oil circuit changeover valve (S62) and 11 13 550 Removing and installing/replacing right oil circuit
changeover valve (S62) .
CAUTION: Reinstall piston, connecting rod and bearing shells back in the same position and in the same installation location.
Conrod and conrod bearing cover are designated with same pair number:
do not interchange / confuse.
In the E52 Series, the oil pump is removed with the upper oil sump section. The procedure is described in the work step Removing and installing upper oil sump section. Refer to 11 13 010 Removing and installing/replacing upper oil sump section (S62) .
In event of heavy oil carbon residue:
Carefully remove oil carbon residue from cylinder wall.
…

BMW Z4 2.8i-3.0i-3.5i-3.5is 2009-2016 Service Manual

Complete digital official shop manual contains service, maintenance, and troubleshooting information for the 2002-2016 BMW Z4 (E85/E86/E89) 2.8i/3.0i/3.5i/3.5is. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual for 2002-2016 BMW Z4 (E85/E86/E89) 2.8i/3.0i/3.5i/3.5is is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

EXCERPT:
SUSPENSION Front Axle – Repair – Z4
3121 WHEEL BEARINGS AND STUB AXLE
31 21 180 REMOVING AND INSTALLING/REPLACING BEARING FOR FRONT WHEEL
Necessary preliminary tasks
 Remove BRAKE DISC
NOTE:  Check brake pads and replace if necessary!
Release screws (1).
Tightening torque 31 21 1AZ .
Press wheel bearing (2) off swivel bearing with a suitable tool.
Installation:
Replace screws.
When reusing, recut all the threads in the wheel bearing.
Keep contact surface (1) of swivel bearing and wheel bearing clean and free from oil and grease.
…
ENGINE
Engine – Repair Instructions – N51, N52, N52K 6-Cylinder
00 ENGINE, GENERAL
00 DANGER OF POISONING IF OIL IS INGESTED/ABSORBED THROUGH THE SKIN Danger of poisoning!
Ingesting oil or absorbing through the skin may cause poisoning!
Possible symptoms are:

Headaches

Dizziness

Stomach aches

Vomiting

Diarrhoea

Cramps/fits

Unconsciousness
Protective measures/rules of conduct:
 Pour oil only into appropriately marked containers
 Do not pour oil into drinking vessels (drinks bottles, glasses, cups or mugs)
 Observe country-specific safety regulations
First aid measures:
 Do not induce vomiting.
If the person affected is still conscious, he/she must rinse out their mouth with water, drink plenty of water and consult a doctor immediately.
If the person affected is unconscious, do not administer anything by mouth, place the person in the recovery position and seek immediate medical attention.
00 RISK OF INJURY IF OIL COMES INTO CONTACT WITH EYES AND SKIN
Danger of injury!
NOTE: Removal and installation procedures apply to 3-Series; 5-Series is similar.
…

BMW Z3 1996-2002

Complete digital official shop manual contains service, maintenance, and troubleshooting information for the BMW Z3 1996-2002. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual for BMW Z3 1996-2002 is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

EXCERPT:
2001-2002 ENGINE Engine Mechanical – Repair Instructions – Z3 Roadster & Coupe (E36)
Fig. 185: Releasing Flywheel
Important!
To prevent damaging valves when fitting the camshafts, no pistons should be in
TDC position.
Lift timing chain and hold under tension.
Rotate engine against direction of engine rotation approx. 30° using the central bolt.
Fig. 186: Lifting Timing Chain
Important!
Bearing cap 1 of inlet camshaft is centered with adapter sleeves.
To prevent inlet camshaft from tilting in bearing strip, release nuts and remove bearing cap 1.
Fig. 187: Identifying Bearing Cap Nuts
Fit special tool 11 3 260 to cylinder head and screw into spark plug threads in cylinders 1 and 4.
Fig. 188: Fitting Special Tool 11 3 260 Into Spark Plug Threads
Turn the eccentric shaft to tension the bearing caps. Unfasten nuts on bearing cover.
Fig. 189: Locating Nuts On Bearing Cover
Relieve tension on eccentric shaft and remove special tool 11 3 260.
Remove bearing covers and place to one side in orderly fashion. Remove camshaft.
Fig. 190: Removing Bearing Covers
Locate bucket tappets in bearing strip with special tool 11 3 250.
Lift out complete bearing strip with bucket tappet.
NOTE: If the cylinder head is then to be removed, remove complete bearing strip with bucket tappets.
NOTE: Only re-use used bucket tappets in the same tappet bore.
Fig. 191: Identifying Special Tool 11 3 250
Check bearing points on bucket tappets for signs of wear (scoring).
Fig. 192: Checking Bearing Points On Bucket Tappets For Signs Of Wear (Scoring)
Bearing strips are marked “A” for exhaust side and “E” for inlet side
Fig. 193: Identifying Bearing Strips Marked “A” For Exhaust Side And “E”
For Inlet Side
Note centering dowels on retaining pins at bearing points 2 and 7.
Fig. 194: Locating Centering Dowels
Install bearing strips.
Installation:
Installation of camshafts is described separately from removal.
The assembly sequence for removal and installation is different.
NOTE: Camshafts, bearings and bearing caps, friction washers, all splines on toothed shafts and spline hubs must be oiled before installation.
…

BMW X6 3.5i, 5.0i, M, ActiveHybrid 2008-2014 Service Manual

Complete digital official shop manual contains service, maintenance, and troubleshooting information for the BMW X6 (E71) 3.5i/5.0i/M/ActiveHybrid 2008-2014. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual for BMW X6 (E71) 3.5i/5.0i/M/ActiveHybrid is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

EXCERPT:
SUSPENSION Steering and Wheel Alignment – Repair Instructions – X6
32 00… GENERAL INFORMATION AND DEFINITIONS
Toe angle difference
a – Toe angle difference
D – Center point of operating circle
The toe angle difference is the angle adjustment of the inner cornering wheel relative to the outer cornering wheel when negotiating a curve. Steering is designed in such a way that angular position of wheels changes as steering lock progresses.
A correctly adjusted toe angle difference produces equal values for left and right lock with consideration of factory tolerances.
Toe angle difference provides information on corresponding operation of steering trapezoid for left or right steering lock from center position.
…