SAMPLE Alexander Dennis Enviro 400
Complete digital official shop manual contains service, maintenance, and troubleshooting information for the Alexander Dennis Dart SLF (Euro3/Euro4), Enviro 400 (EURO3/EURO4&4+) Bus. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.
This manual for Alexander Dennis Dart SLF (Euro3/Euro4), Enviro 400 (EURO3/EURO4&4+) Bus is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.
MAKE: Alexander Dennis
MODEL: Dart SLF (Euro3/Euro4), Enviro 400 (EURO3/EURO4&4+)
FORMAT: PDF
2197:
Dart SLF Euro 3 – 4 Cylinder Parts Manual
Date: Nov 2001 (05/06); 280 pages
2209:
Dart SLF Euro 3 Service Manual
Date: Nov 2001 (01/06); 378 pages
2225:
Dart 4 & 6 cylinder/ Pointer Operation Guide
Date: September 2003 (03/04); 72 pages
2266:
Dart 4 & 6 cylinder/ Pointer Operation Guide
Date: October 2003 (08/05); 72 pages
2291:
Enviro 400 (EURO 4&4+) 4 & 6 cylinder Service Manual
Date: July 2006 (03/08); 474 pages
2292:
Enviro 400 (EURO 3) Service Manual
Date: December 2005 (03/06); 450 pages
2297:
Enviro 400 (EURO 4&4+) Service Manual
Date: March 2006 (10/07); 466 pages
2300:
Dart E4 Pointer Handbook
2301:
Dart Euro 4 Parts Manual
Covering EURO 4 CHASSIS 4-CYLINDER MODELS: SFD1HFCR56GW1, SFD1HFCR56GW9, SFD2HFCR56GW9
Publication Number: 2301 Date: October 2006
2302:
Dart SLF Euro 4 – 4 Cylinder Models Service Manual
Date: September 2006; 294 pages
EXCERPT:
Air Cleaner – Amended:
Description
The air cleaner is fitted on the nearside of the vehicle. The cleaner encloses a pleated filter element which is treated to combat premature blockage by exhaust carbon.
A remote restriction indicator is connected to the outlet to indicate clogging.
Maintenance
Access is obtained through the rear engine door. The element should be changed if the restriction indicator (fitted adjacent to the rear EDC) shows red. It is not recommended that treated elements should be washed as this removes the active chemical. In a case of necessity the element can be cleaned by blowing through with air at a max 100 p.s.i. (7 bar) in the reverse direction. To remove the element, undo the centre hand nut on the cleaner casing lid. Pull out the element and wipe out the inside of the casing with a damp cloth. Check that the gaskets are in good condition and that the casing and lid are undamaged. Fit the new element, position the lid and tighten the hand nut. If necessary reset the restriction indicator by pressing down on the top.
Vehicle checks
After reassembly but before restarting engine, the following system checks must be carried out.
a. Check all cleaner to engine pipe work for defects to ensure good and leak free condition.
b. Check that all rubber hose connections are tight and leak free. Renew any worn or damaged parts.
c. Check that the cleaner mounting fixtures are secure.
Restriction Indicator
The restriction indicator gives a warning that the air cleaner filter is too clogged for further service. The indicator is operated by the depression between the air cleaner and the engine, and at a preset figure, the red warning indicator will remain locked up in a visible position after the engine has stopped running.
When the red indicator band appears, the air cleaner element must be removed and renewed. After the element has been renewed, reset the indicator by pushing on the diaphragm at the top of the instrument. Blank off the connection if the indicator is not fitted.
…