INSTANT DOWNLOAD (add to cart)
Case 580N/580SN/580SN-WT/590SN Workshop Repair & Service Manual
6,600+ pages, bookmarked, Searchable, Printable, high quality PDF
MAKE: Case
MODEL: 580N, 580SN, 580SN-WT, 590SN Tractor Loader Backhoe
FORMAT: PDF
PAGES / SIZE: PDF (902 MB)
“47365539.pdf”
3,501 pages
580N, 580SN WT (580 Super N WT), 580SN, 590SN Service Manual
47365539 08/07/2012
“84261053.pdf”
580N, 580SN-WT, 580SN, 590SN Loader Backhoe Operator’s Manual
330 pages
Part number 84482502
2nd edition English
October 2011
Replaces part number 84261053
“84516378.pdf”
580N, 580SN-WT, 580SN, 590SN Tractor Loader Backhoe Service Manual
2,895 pages
Part number 84516378
English
July 2011
Replaces part number 84390833
“84540378.pdf”
151 pages
ENGINE AND PTO IN – B
580N, 580SN-WT, 580SN, 590SN Tractor Loader Backhoe Service Manual
Part number 84540378
English
July 2011
Replaces part number 84393971
Complete digital official shop manual contains service, maintenance, and troubleshooting information for the for Case 580N, 580SN, 580SN-WT, 590SN Tractor Loader Backhoe. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your Case 580N/580SN/580SN-WT/590SN like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.
This manual for Case 580N, 580SN, 580SN-WT, 590SN Tractor Loader Backhoe is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.
EXCERPT:
Contents
INTRODUCTION
HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS A
PRIMARY HYDRAULIC POWER SYSTEM … A.10.A
SECONDARY HYDRAULIC POWER SYSTEM.. A.12.A
ELECTRICAL POWER SYSTEM .. A.30.A
FAULT CODES … . A.50.A
ENGINE AND PTO IN … B
ENGINE .. . B.10.A
FUEL AND INJECTION SYSTEM.. B.20.A
EXHAUST SYSTEM… . B.40.A
ENGINE COOLANT SYSTEM .. . B.50.A
STARTING SYSTEM … . B.80.A
TRANSMISSION, DRIVE AND PTO OUT … C
TRANSMISSION Power Shuttle.. . C.20.C
TRANSMISSION Power-shift .. . C.20.E
AXLES, BRAKES AND STEERING.. D
FRONT AXLE … . D.10.A
REAR AXLE .. D.12.A
STEERING Hydraulic… . D.20.C
SERVICE BRAKE Hydraulic.. . D.30.C
PARKING BRAKE Mechanical .. . D.32.B
WHEELS AND TRACKS Wheels.. . D.50.C
FRAME AND CAB … E
FRAME Primary frame … E.10.B
SHIELD .. . E.20.A
USER CONTROLS AND SEAT .. . E.32.A
USER CONTROLS AND SEAT Operator seat .. . E.32.C
USER PLATFORM …E.34.A
ENVIRONMENT CONTROL Air-conditioning system .. . E.40.C
FRAME POSITIONING .. F
STABILIZING Working stabilizing .. F.20.D
TOOL POSITIONING … G
LIFTING .. . G.10.A
HITCH AND WORKING TOOL .. H
BOOM Lift .. . H.20.B
BOOM Swing …H.20.D
DIPPER Lift.. . H.25.B
DIPPER Extension … . H.25.F
ARM TOOL ATTACHMENT Tilt.. . H.30.C
EXCAVATING AND LANDSCAPING … J
DIGGING Non-articulated digging tools … . J.20.B
CARRYING Articulated tools .. . J.50.C
TRANSMISSION, DRIVE AND PTO OUT – TRANSMISSION Power Shuttle
TRANSMISSION Power Shuttle – Test – Checking Differential Lock Valve
CAS-1804 Pressure Test Kit
CAS-1808 Flowmeter Fitting Kit
NOTE: See TRANSMISSION Power Shuttle – Tool connection Two Wheel Drive Port Identification (C.20.C) or TRANSMISSION Power Shuttle – Tool connection Four Wheel Drive Port Identification (C.20.C) for test port locations.
1. Engage the parking brake.
2. Place the transmission in neutral.
3. Start the engine. The oil should be at normal operating temperatures.
4. Connect a pressure test fitting and a 42 bar (600 psi) gauge to test port 7 (A).
5. With the transmission shift lever in Neutral, put the directional control lever in Forward or Reverse.
6. Run the engine at 2200 RPM.
7. Press and hold the differential lock switch located in the loader control valve.
8. Monitor the gauge and record the values for low idle, see TRANSMISSION Power Shuttle – Pressure test – 2 Wheel Drive, Test One — Engine at Idle 900 to 1100 rpm (C.20.C) or TRANSMISSION
Power Shuttle – Pressure test – 4 Wheel
Drive, Test One — Engine at Idle 900 to 1100 rpm (C.20.C).
9. Monitor the gauge and record the values for full throttle, see TRANSMISSION Power Shuttle – Pressure test — 2 Wheel Drive, Test Two — Engine at 2200 rpm (C.20.C) or TRANSMISSION Power Shuttle –
Pressure test — 4 Wheel Drive, Test Two — Engine at 2200 rpm (C.20.C).
…