Fiat Seicento 1997-2010 Workshop Repair & Service Manual (COMPLETE & INFORMATIVE for DIY REPAIR) ☆ ☆ ☆ ☆ ☆
* COMPLETE, Absolutely No Missing Pages!
* Official Service INFORMATION You Can Count On!
* Customer Satisfaction GUARANTEED!
This high QUALITY official manual for Fiat Seicento 1997-2010 is 100 percents COMPLETE and INTACT, no MISSING, CORRUPT pages, sections to freak you out! This manual is exactly as described. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices.
FORMAT: PDF
LANGUAGE: English
SIZE/PAGE: 461 MB
OS: Windows/Mac OS X/Linux/Android/iOS
MAKE: FIAT
YEAR: 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010
MODEL: Seicento (Type 187) (aka Fiat 600)
INSTANT DELIVERY: A download link will be sent to you instantly after payment. Simply click on the link and save it to your computer. You can use this Manual as long as you wish with no restrictions.
CUSTOMER SATISFACTION: If there is ANY kind of problem with the item you purchased, just drop a quick email. Within HOURS the issue shall be taken care of.
PRINTABLE MANUAL WITH DIAGRAMS: Just print the manual out and start to work. You can also use the manual with your Tablet/Laptop in your garage.
REFUND/EXCHANGE POLICY: We sell high QUALITY products only. However if you encounter any problems with the item you purchased, another replacement link will be sent to you. If we’re at fault, you will get 100 percents refund.
Buy ☆THE BEST MANUAL ON THE INTERNET☆ from responsible seller and get instant download now without uncertainty or surprise.
This highly detailed workshop service repair manual for download contains virtually everything you will ever need to repair, maintain, rebuild, refurbish or restore Fiat Seicento 1997-2010. All diagnostic and repair procedures and gives you access to the same information that professional technicians and mechanics have. You can view and print out the complete repair procedures with this workshop service repair manual Download – you do not need to be skilled with a computer.
EXCERPTS:
1040A FUEL TANK AND COMPONENTS
FUEL FILLER
The fuel filler cap is fitted with two valves which enable the following if the multi-function valve fails:
– they ventilate the tank if a vacuum is created
– they bleed fuel fumes if excessive pressure is created in the tank.
Tank ventilation
If a vacuum exceeding a pre-set threshold is created in the tank, it operates plate (1) and pulls backward the overcoming spring (2).
This allows tank ventilation via the round sections created between plate (1) and seal (3).
Fuel fume bleeding When the pressure of fuel fumes on plate (4) exceeds a pre-set value, spring (5) load is overcome.
This opens a round section between plate (4) and seal (3).
FUEL PUMP
This pump is equipped with a plastic impeller designed for petrol with or without ethylene.
A no return valve (3) and an overpressure valve set to 2.6 bar (2) are located inside the tank.
The pump is directly powered by the ECU as to:
– stop operation in the event of engine ratio falling under a pre-set threshold
– time ( 15 seconds) its operation whenever the key is turned to MAR
– enable operation during movement or when the engine is running.
Operation
A steel ball (1) is fitted in a conic seat (2). It is normally held in position by a magnet.
With certain specific acceleration loads, the ball is freed from the magnetic attraction and gradually moves upwards out of its conical seat according to the angle of the cone.
A fast release mechanism (3) is located over the ball. This usually creates a normally closed (NC) electric circuit.
When the mechanism is hit by the ball it shifts the NC circuit to normally open (NO) thus cutting the fuel pump earth circuit.
The inertia switch can be restored by pressing the button covered by a flexible guard (4).
Note: If even after a slight crash you can smell fuel or if you notice leakages from the fuel feed system to not reset the inertia switch.
Seek the cause of the problem and solve it before resetting the switch to avoid the risk of fire.
Operation
When the engine is off, the sensor membrane bends according to the atmospheric pressure.
When the key is inserted it provides the ECU information on the altitude.
When the engine is started, the vacuum in the intake manifold acts on the sensor membrane via the connection pipe. The membrane bends and this varies the resistance value.
As the sensor is powered at constant voltage (5 Volt) by the ECU, varying the resistance also varies the output voltage according to the diagram shown in the illustration.
This signal provides the ECU initial data on the amount of intake air.