INSTANT DOWNLOAD (add to cart)
Hyundai Tiburon 1996-2009 Workshop Repair & Service Manual
Complete digital official shop manual contains service, maintenance, and troubleshooting information for the Hyundai Tiburon 1996-2009. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.
This manual for Hyundai Tiburon 1996-2009 is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.
FILELIST:
’03-’06 Tiburon.pdf
Body Repair Manual.pdf
Electrical Troubleshooting Manual.pdf
Owners Manual.pdf
Shop Manual.pdf
Tiburon (2003-2008).zip
EXCERPT:
Automatic Transaxle System > Automatic Transaxle System > Automatic Transaxle >
Components and Components Location (F4A42-2)
Automatic Transaxle System > Automatic Transaxle System > Automatic Transaxle >
Repair procedures (F4A42-2)
REMOVAL
1. Remove the engine cover.
2. Remove the battery terminal.
3. Remove the air duct.
4. Remove the battery tray.
5. Remove the air cleaner.
(1) Upper
(2) Lower
6. After removing the CKP sensor, O2 sensor and oil pressure switch wiring bracket, separate the connectors.
7. Remove the speedometer sensor connector.
8. Remove the transaxle range switch.
9. Remove the oil cooler hose.
10. Remove the clip(transaxle side) of the shift cable.
11. Separate the steering column shaft joint.
12. Separate the power steering oil pump hose.
Be careful not to leak after separating.
13. Separate the hose after removing the clip of the power steering return hose.
14. Remove the upper connecting transaxle bolt.
15. Separate the start motor.
16. Install the engine support fixture.
17. After removing the tire, remove the caliper.
18. Remove the transaxle side cover.
19. Remove the transaxle under cover.
20. Separate the tie rod end.
21. Remove the wheel speed sensor and the knuckle mounting bolt.
22. Drain the oil.
23. Remove the transaxle mounting bracket.
(1) Insulator bolt
(2) Body mounting bolt (Upper)
(3) Body mounting bolt (Side)
(4) Transaxle side mounting bolt
24. Remove the front roll stopper.
(1) Insulator bolt
(2) Stopper bolt (Upper)
(3) Stopper bolt (Lower)
25. Remove the rear roll stopper.
(1) Insulator bolt
(2) Stopper bolt
26. Remove the drive shaft.
27. Remove the front muffler.
28. Remove the sub frame mounting bolt.
29. Install the jack under the transaxle assembly
30. Remove the transaxle lower mounting bolt to the engine.
31. Remove the transaxle assembly.
INSTALLATION
1. Attach the torque converter on the transaxle side and mount the transaxle assembly onto the engine.
If the torque converter is mounted first on the engine, the oil seal on the transaxle may be damaged. Therefore, first be sure to assemble the torque converter to the transaxle.
2. Install the transaxle control cable and adjust as follows:
(1) Move the shift lever and the transaxle range switch to the “N” position and install the control cable.
(2) When connecting the control cable to the transaxle mounting bracket, install the clip until it contacts to the control cable.
(3) Remove any free-play in the control cable by adjusting the nut and then check to see that the selected lever moves smoothly.
(4) Check to see that the control cable has been adjusted correctly.
Automatic Transaxle System > Automatic Transaxle Control System > Transaxle Shift
Control > Components and Components Location (F4A42-2)
COMPONENTS
…