INSTANT DOWNLOAD (add to cart)
Complete workshop & service manual with electrical wiring diagrams for New Holland TG Series Tractors (TG210, TG230, TG255, TG285). It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.
New Holland TG Series Tractors (TG210, TG230, TG255, TG285) service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.
3,098 pages, bookmarked, Searchable, Printable, high quality PDF
New Holland TG Series Tractors (TG210, TG230, TG255, TG285) Repair Manual
3,098 pages, 708 MB PDF
87057613 Issued 11-02 / Revised 01-05
COMPLETE TABLE OF CONTENTS
Standard Torque Specifications
Safety, General Information/Maintenance Schedule
General Specifications and Special Torques
Engine Removal and Installation
Fuel Tank Removal and Installation
Radiator, Coolers and Condenser – Removal and Installation
8.3L, 24 Valve Engine Introduction
8.3L, 24 Valve Engine Identification
8.3L, 24 Valve Engine Troubleshooting Symptoms
8.3L, 24 Valve Engine Cylinder Block
8.3L, 24 Valve Engine Cylinder Head
8.3L, 24 Valve Engine Rocker Levers
8.3L, 24 Valve Engine Cam Followers
8.3L, 24 Valve Engine Fuel System
8.3L, 24 Valve Engine Injectors and Fuel Lines
8.3L, 24 Valve Engine Lubricating Oil System
8.3L, 24 Valve Engine Cooling System
8.3L, 24 Valve Engine Drive Units
8.3L, 24 Valve Engine Air Intake System
8.3L, 24 Valve Engine Exhaust System
8.3L, 24 Valve Engine Miscellaneous
8.3L, 24 Valve Engine Specifications
8.3L, 24 Valve Engine Fuel System – Introduction
8.3L, 24 Valve Engine Fuel System – System Identification
8.3L, 24 Valve Engine Fuel System – Familiarization
8.3L, 24 Valve Engine Fuel System – Troubleshooting Fault Codes
8.3L, 24 Valve Engine Fuel System – Troubleshooting Symptoms
8.3L, 24 Valve Engine Fuel System – Electronic Engine Controls
8.3L, 24 Valve Engine Fuel System – Specifications
Viscous Fan Drive Test (Service Bulletin)
Power Take Off Control System How it Works
Powershift Transmission System How it Works and Troubleshooting
Front Frame to Speed Transmission Split
Speed to Range Transmission Split
Speed Transmission
Range Transmission to Rear Frame Split
Range Transmission
Transmission Control Valves and inching Valve
Rear Frame
Hydraulic Pump Drive
Mechanical Front Drive MFD Control System How it Works
Differential Lock Control System How it Works
MFD Clutch Removal Without Tractor Split
MFD Driveshaft Removal and Installation
Suspended MFD Axle Removal
Supersteer Axle Removal
Limited Slip FWD Differential
Locking MFD Differential
MFD Planetary Hub, Steering Knuckle, and Axle Drive Shaft
Suspended FWD Axle
Supersteer Axle Vertical Control Linkage
Suspended FWD Axle System
Rear Axle and Planetaries
Brake Valve
Brake Cylinders
Park Brake
Trailer Brakes How It Works
How to Read Symbols in a Hydraulic Schematic
Hydraulic Systems How it Works and Troubleshooting
PTO and Differential Lock Valve
Remote Valve and Coupler Service
Remote Hydraulic System How it Works and Troubleshooting
Priority and Regulator Valve
Charge Pump
CCLS Piston Pump And Hydraulic Filter
Hitch System How it Works
Hitch Control Valve
Air Conditioning Troubleshooting
Air Conditioner System Service
Electrical System How It Works and Troubleshooting (Prior to P.I.N. JAW 129992)
Standard Instrumentation Programming and Fault Codes
Hitch Controller Calibration and Fault Codes
Transmission Controller
(With Suspended Axle) Calibration and Fault Codes
Armrest Controller Calibration and Fault Codes
Remote Hydraulics Controller Fault Codes
PTO Controller Configuration and Fault Codes
Performance Monitor Controller Fault Codes
Pedal and Pedal Switch Adjustment
Cab Raise/Removal and Installation
Service Information packaged with 87012641
INSITE Professional – Operation / ESDN – ECM Software Installation – 87012632 Electronic Service Tool – Users Guide 87025502
Electrical Schematic (Prior to P.I.N. JAW129992) – 87025177
Electrical Schematic (P.I.N. JAW129992 and After) – 87054643
Hydraulic Schematic – 87025178 Loctite Product Chart – 8-98902
…
EXCERPT:
24 Valve, 8.3 Liter Engine Miscellaneous
Cup Plug (017-002)
Remove (017-002-002)
Use a center punch to mark the cup plug for drilling.
CAUTION
Do not allow metal shavings to fall in the engine when drilling a hole in the cup plug. Damage to engine components can occur.
Drill an 1/8-inch hole into the cup plug.
Use a dent puller to remove the plug.
Discard all used cup plugs. Do not use them again.
Cup Plug (017-002)
Clean (017-002-006)
Thoroughly clean the cup plug hole using Scotch-Brite, or equivalent. Use spray cleaner or equivalent, to perform a final clean of the bore.
Inspect for Reuse (017-002-007)
Inspect the cup plug bores for damage.
…