INSTANT DOWNLOAD (add to cart)
Sterling Bullet (CONV45, CONV55) Models Factory Service & Shop Manual
Complete workshop & service manual with electrical wiring diagrams for Sterling Bullet (CONV45, CONV55) Models. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.
This Sterling Bullet (CONV45, CONV55) Models service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.
“STI-488-08 (11_07P).pdf”
Sterling Bullet Workshop Manual
Models: CONV45, CONV55
STI-488-08 (11/07P); 5,716 pages
Workshop Manual Contents
. . . Introduction
00 . . . Lubrication and Maintenance
02 . . . Suspension
03 . . . Differential and Driveline
04 . . . Vehicle Quick Reference
05 . . . Brakes
06 . . . Clutch
07 . . . Cooling
08A . . . Audio/Video
08B . . . Chime/Buzzer
08E . . . Electronic Control Modules
08F . . . Engine Systems
08G . . . Heated Systems
08H . . . Horn
08I . . . Ignition Control
08J . . . Instrument Cluster
08L . . . Lamps
08M . . . Message Systems
08N . . . Power Systems
08O . . . Restraints
08P . . . Speed Control
08Q . . . Vehicle Theft Security
08R . . . Wiper/Washers
08T . . . Navigation/Telecommunication
08W . . . Wiring
09 . . . Engine
11 . . . Exhaust System
13 . . . Frame and Bumpers
14 . . . Fuel System
19 . . . Steering
21 . . . Transmission and Transfer Case
22 . . . Tires/Wheels
23 . . . Body
24 . . . Heating and Air Conditioning
25 . . . Emissions Control
— — — — — — — — — — — — — — — — — — — — — — — — — — —
“STI-488-09 (11_08P).pdf”
Sterling 2009 Bullet Workshop Manual
Models: CONV45, CONV55
STI-488-09 (11/08P); 5,924 pages
Workshop Manual Contents
. . . Introduction
00 . . . Vehicle Data
02 . . . Front Suspension
03 . . . Differential and Driveline
04 . . . Vehicle Quick Reference
05 . . . Brakes
06 . . . Clutch
07 . . . Cooling
08A . . . Audio
08B . . . Chime/Buzzer
08E . . . Electronic Control Modules
08F . . . Battery System
08G . . . Heated/Cooled Systems
08H . . . Horn
08I . . . Ignition Control
08J . . . Instrument Cluster
08L . . . Lamps and Lighting
08M . . . Message Systems
08N . . . Power Systems
08P . . . Speed Control
08Q . . . Vehicle Theft Security
08R . . . Wiper/Washers
08T . . . Navigation/Telecommunication
08W . . . Wiring
09 . . . Engine
10 . . . Restraints
11 . . . Exhaust System
13 . . . Frame and Bumpers
14 . . . Fuel System
17 . . . Rear Suspension
19 . . . Steering
21 . . . Transmission and Transfer Case
22 . . . Tires/Wheels
23 . . . Body
24 . . . Heating and Air Conditioning
25 . . . Emissions Control
28 . . . DTC-Based Diagnostics
29 . . . Non-DTC Diagnostics
— — — — — — — — — — — — — — — — — — — — — — — — — — —
“Driver’s and Maintenance Manual (’09).pdf”
Sterling Bullet Trucks Driver’s and Maintenance Manual 2009; 531 pages
EXCERPT:
8A – 28 Audio
Removal
WARNING: Disable the airbag system before attempting any steering wheel, steering column, seat belt tensioner, side airbag or instrument panel component diagnosis or service. Disconnect and isolate the negative battery (ground) cable. Wait two minutes for the airbag system capacitor to discharge before performing further diagnosis or service. This is the only sure way to disable the airbag system. Failure to follow these instructions may result in accidental airbag deployment and possible serious or fatal injury.
1. Disconnect and isolate the battery negative cable.
2. Remove the driver airbag (Refer to 10 – Restraints/AIR BAG, Driver – Removal).
3. Remove the speed control switches (2) (Refer to 08 – Electrical/8P – Speed Control/SWITCH, Speed Control – Removal).
4. Unplug the wire harness connector from the remote radio switch (1).
5. Depress the tabs on each side of each switch and push the switch through the rear steering wheel cover.
Installation
WARNING: Disable the airbag system before attempting any steering wheel, steering column, seat belt tensioner, side airbag or instrument panel component diagnosis or service. Disconnect and isolate the negative battery (ground) cable. Wait two minutes for the airbag system capacitor to discharge before performing further diagnosis or service. This is the only sure way to disable the airbag system. Failure to follow these instructions may result in accidental airbag deployment and possible serious or fatal injury.
1. Install remote radio switch (1) to the steering wheel.
2. Connect the wire harness to the remote radio switch.
3. Install the speed control switches (2) (Refer to 08 – Electrical/8P – Speed Control/SWITCH, Speed Control – Installation).
4. Install the driver airbag (Refer to 10 – Restraints/AIR BAG, Driver – Installation).
5. Connect the battery negative cable.
…