INSTANT DOWNLOAD (add to cart)
Complete digital official shop manual contains service, maintenance, and troubleshooting information for the Toyota Van 1982-1991. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your Van like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.
This manual for Toyota Van 1982-1991 is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.
MAKE: Toyota
YEAR: 1982 1983 1984 1985 1986 1987 1988 1989 1990 1991
Model: Van (YR 22, 29, 31, 32 Series) (a.k.a. TownAce van, MasterAce Surf van, Model F, Toyota Tarago, Space Cruiser, Daihatsu Delta Wide)
EXCERPT:
1987 TOYOTA VAN
REPAIR MANUAL
INTRODUCTION
MAINTENANCE
ENGINE MECHANICAL
EMISSION CONTROL SYSTEMS
EFI SYSTEM
COOLING SYSTEM
LUBRICATION SYSTEM
IGNITION SYSTEM
STARTING SYSTEM
CHARGING SYSTEM
CLUTCH
MANUAL TRANSMISSION
AUTOMATIC TRANSMISSION
TRANSFER
PROPELLER SHAFT
FRONT AXLE AND SUSPENSION
REAR AXLE AND SUSPENSION
BRAKE SYSTEM
STEERING
BODY ELECTRICAL SYSTEM ]
BODY
AIR CONDITIONING SYSTEM
SERVICE SPECIFICATIONS
STANDARD BOLT TORQUE SPECIFICATIONS
SSTAND SSM
AUTOMATIC TRANSMISSION
HYDRAULIC CIRCUIT
ELECTRICAL WIRING DIAGRAM
…
ENGINE MECHANICAL – Cylinder Head
PREPARATION FOR REMOVAL (See page EM-9)
1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY
2. REMOVE RIGHT SEAT
3. REMOVE ENGINE SERVICE HOLE COVER
4. DRAIN COOLANT
Open the radiator and engine drain cocks, and allow coolant to drain into a clean container.
5. DRAIN ENGINE OIL
6. [w/ PS]
REMOVE POWER STEERING PUMP (See page SR-29)
7. REMOVE EXHAUST PIPE AND BRACKET
8. DISCONNECT ACCELERATOR CABLE WITH BRACKET FROM THROTTLE BODY
9. REMOVE AIR CLEANER PIPE AND HOSES
10. DISCONNECT WATER TEMPERATURE SENDER GAUGE CONNECTOR FROM CYLINDER HEAD
11. DISCONNECT EFI CONNECTORS
(a) Water thermo sensor connector
(b) Cold start injector time switch connector
(c) Cold start injector connector
(d) Air valve connector
(e) Throttle position sensor connector
(f) [2WD M/T] Oxygen sensor connector
(g) [w/ A/C]
Water temperature switch connector
12. DISCONNECT HOSES
(a) Radiator inlet hose
(b) Radiator breather hose
(c) Reserve tank hose
(d) Heater outlet hose
(e) PCV hoses
(f) Water by-pass hoses
13. DISCONNECT VACUUM HOSES
(a) Brake booster vacuum hose
(b) Charcoal canister hose
(c) Label and disconnect emission control hoses
14. REMOVE THROTTLE BODY
Remove the throttle body from the air intake chamber.
15. REMOVE EGR VALVE
(a) Remove the two nuts from the air intake chamber.
(b) Remove the union nut from exhaust manifold and EGR valve.
16. DISCONNECT PIPE AND HOSES
(a) Cold start injector pipe
(b) Water by-pass hoses
(c) Pressure regulator hose
17. REMOVE AIR INTAKE CHAMBER
(a) Remove the air intake chamber brackets.
NOTE: Use a 1 2 mm socket wrench to remove the rear chamber bracket.
(b) Remove the air intake chamber with the air valve.
NOTE: Use 1 0 mm and 1 2 mm socket wrenches to remove the air intake chamber with the air valve.
18. DISCONNECT INJECTOR CONNECTOR
(a) Remove the wire clamp bolt.
(b) Disconnect the injector connectors from the injectors.
19. REMOVE PARTS
(a) Exhaust manifold bracket
(b) Heater pipe bracket
(c) Fuel inlet pipe union bolt from fuel filter
(d) Fuel outlet hose
REMOVAL OF CYLINDER HEAD (See page EM-9)
1. REMOVE SPARK PLUGS AND TUBES
2. REMOVE CYLINDER HEAD COVER
Remove the cap nuts, seal washers, cylinder head cover and gasket.
3. REMOVE ROCKER ARM SHAFT ASSEMBLY
(a) Uniformly loosen and remove the three bolts and two nuts in several passes, in sequence shown.
(b) Remove the rocker shaft assembly.
4. REMOVE PUSH RODS
NOTE: Keep the push rods in correct order.
5. REMOVE CYLINDER HEAD
(a) Uniformly loosen and remove the thirteen head bolts in several passes, in the sequence shown.
CAUTION: Head warpage or cracking could result from bolts removing in incorrect order.
…