PageLarge

INSTANT DOWNLOAD (add to cart)

Complete workshop & service manual with electrical wiring diagrams for Nissan Serena (C23), Silvia (S14-S15), Stanza (T12/U12). It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

Nissan Serena (C23), Silvia (S14-S15), Stanza (T12/U12) service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

2,000+ pages, bookmarked, Searchable, Printable, high quality PDF

’89 Stanza (T12).pdf
’90 Stanza (U12).pdf
’91 Stanza (U12).pdf
’92 Stanza (U12).pdf
Model A10 Series BE.pdf
Model A10 Series Wiring Diagram.pdf
Serena (Model С23 Series).pdf
Silvia S14.pdf
Silvia S15

EXCERPT:
AIR BLEEDING PROCEDURE
Bleed air from clutch piping connector according to the following procedure.
Carefully monitor fluid level at master cylinder during bleeding operation.
Top up reservoir with recommended brake fluid.
Connect a transparent vinyl tube to air bleeder valve.
Slowly depress the clutch pedal to its full stroke and release it completely. Repeat this operation several times at 2 to 3 seconds intervals.
Open the air bleeder with the clutch pedal fully depressed.
Close the air bleeder.
Release the clutch pedal and wait at least 5 seconds.
Repeat steps c through f mentioned above, then air bubbles will no longer appear at the damper in the brake fluid.
Bleed air from clutch operating cylinder according to the above procedure.
Repeat the above air bleeding procedures 1 and 2 several times.
…

INSTANT DOWNLOAD (add to cart)

Complete digital official shop manual contains service, maintenance, and troubleshooting information for the 1983-2015 Nissan Sentra (B11/B12/B13/B14/B15/B16/B17) . Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual for Nissan Sentra, Sentra E, Sentra CA, Sentra FE+S, Sentra FE+SV, Sentra FE-S, Sentra FE-SV, Sentra GLE, Sentra GXE, Sentra LE, Sentra MPG, Sentra S, Sentra SE, Sentra SE-R, Sentra SE-R Spec V, Sentra SL, Sentra SR, Sentra SV, Sentra XE is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

EXCERPT:
ENGINE – SECTION FL – FUEL SYSTEM
DISASSEMBLY AND ASSEMBLY
FUEL LEVEL SENSOR UNIT
Exploded View
1. Fuel filter and pump assembly 2. Fuel level sensor unit 3. Float arm assembly
4. Fuel tank temperature sensor 5. Fuel level sensor unit/fuel tank temperature sensor harness connector
Disassembly and Assembly
DISASSEMBLY
1. Disconnect the harness connector (1) from fuel level sensor unit/fuel tank temperature sensor.
NOTE: Hold connector with your fingers, because there is no tab for releasing stopper. Pull it out straight downward.
2. Remove fuel tank temperature sensor (2) from fuel filter and fuel pump assembly (1).
3. Remove fuel level sensor unit (3) from fuel filter and fuel pump assembly (1) using a suitable tool (2).
CAUTION:
• Be careful not to damage the fuel level sensor unit.
• Do not disassemble fuel filter and fuel pump assembly.
ASSEMBLY
1. Check for damage of fuel level sensor unit installation position on the side of fuel filter and pump assembly.
2. Slide fuel level sensor unit until it aligns to installation groove, then insert it until it stops.
• After inserting, apply force in reverse direction (removal direction) to ensure it cannot be pulled out.
3. Connect fuel level sensor unit/fuel tank temperature sensor harness connector.
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leaks.
1. Turn ignition switch “ON” (with engine stopped), then check connections for leaks by applying fuel pressure to fuel piping.
2. Start engine and let it idle and check there are no fuel leaks at the fuel system connections.
…

INSTANT DOWNLOAD (add to cart)

Nissan Rogue 2008-2016 Workshop Repair & Service Manual

Complete digital official shop manual contains service, maintenance, and troubleshooting information for the Nissan Rogue (S35/T32 Series) 2008-2016. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual for Nissan Rogue, Rogue Krom, Rogue S, Rogue Select S, Rogue SL, Rogue SV is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

EXCERPT:
BRAKES
PARKING BRAKE SYSTEM
Removal and Installation
REMOVAL
1. Remove instrument lower panel LH. Refer to IP-23, “Removal and Installation”.
2. Remove the knee protector. Refer to IP-14, “Exploded View”.
3. Disconnect the harness connector from the parking brake switch.
4. Remove the parking brake switch.
5. Remove the parking brake control nuts and remove the parking brake control.
6. Remove adjusting nut from parking brake control.
7. Disconnect the parking brake front cable from the parking brake control.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not reuse the adjusting nut.
• Adjust the parking brake with new adjusting nut.Refer to PB-4, “Inspection and Adjustment”.
PARKING BRAKE FRONT CABLE
Removal and Installation INFOID:0000000012427233
REMOVAL
1. Disconnect the positive and negative battery terminals. Refer to PG-80, “Removal and Installation (Battery)”
2. Remove the parking brake control. Refer to PB-8, “Removal and Installation”
3. Remove driver seat (LH). Refer to SE-32, “DRIVER SIDE : Removal and Installation”.
4. Remove the center console. Refer to IP-19, “Removal and Installation”.
5. Remove front door welts (LH). Refer to INT-23, “BODY SIDE WELT : Removal and Installation – Front
Door Welt”.
6. Remove dash side finisher (LH). Refer to INT-24, “DASH SIDE FINISHER : Removal and Installation”.
7. Remove shift selector knob. Refer to TM-193, “Exploded View”.
8. Remove the front floor connecting ducts (LH/RH). Refer to VTL-10, “FRONT FLOOR DUCT : Removal and Installation – Front Floor Connecting Duct”.
9. Remove the front floor duct. Refer to VTL-11, “FRONT FLOOR DUCT : Removal and Installation – Front Floor Duct”
10. Remove the rear center ventilator duct. Refer to VTL-9, “CENTER VENTILATOR DUCT : Removal and Installation”.
11. Release clips (A) using a suitable tool and remove steering joint floor cover (1).
12. Place front floor trim aside and remove the front floor spacer. Refer to INT-26, “Exploded View”.
13. Remove the bolts from the parking brake front cable mount. Refer to PB-7, “Exploded View”.
14. Pull equalizer (A) of the parking brake front cable (1) in a rearward
direction and then push upward to separate each parking brake rear cable (2) from the parking brake front cable (1).
CAUTION: To prevent damage to the parts, do not bend the parking brake cables.
15. Remove the parking brake front cable.
INSTALLATION
Installation is in the reverse order of removal.
…

INSTANT DOWNLOAD (add to cart)

Complete digital official shop manual contains service, maintenance, and troubleshooting information for the 1993-2016 Nissan Quest (V40/V41/V42/(R)E52 Series) . Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual for 1993-2016 Nissan Quest, Quest GLE, Quest GXE, Quest LE, Quest Platinum, Quest S, Quest SE, Quest SL, Quest SV, Quest XE is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

EXCERPT:
DRIVER INFORMATION & MULTIMEDIA
METER, WARNING LAMP & INDICATOR
FUEL GAUGE : System Description INFOID:0000000011324088
SYSTEM DIAGRAM
DESCRIPTION
Control Outline
The combination meter reads the fuel level sensor signal from the fuel level sensor unit and indicates the fuel level to the fuel gauge.
Refuel Control
The combination meter accelerates the fuel gauge if the all conditions listed below are met, or the ignition switch is ON from OFF.
• Ignition switch is ON position.
• The vehicle is not moving.
• The fuel level change by 15 (4 US gal, 3-1/4 Imp gal) or more.
OIL PRESSURE WARNING LAMP
OIL PRESSURE WARNING LAMP : System Description
SYSTEM DIAGRAM
DESCRIPTION
The combination meter turns the oil pressure warning lamp ON when receiving ECM to the oil pressure warning lamp signal via CAN communication. For details, refer to EC-25, “Engine Oil Pressure Sensor”.
MASTER WARNING LAMP
MASTER WARNING LAMP: System Description INFOID:0000000011324090
SYSTEM DIAGRAM
DESCRIPTION
When receiving a signal from each unit, switch, or sensor, the combination meter turns ON/OFF the master warning lamp in synchronization with the following warnings on the information display.
• Door open warning
• Parking brake release warning
• Low fuel warning
• Low washer fluid warning
• NO KEY warning
• Low tire pressure warning
• Fuel filler cap warning
NOTE: For details on warnings displayed on the information display, refer to MWI-21, “INFORMATION DISPLAY : System Description”.
…

INSTANT DOWNLOAD (add to cart)

Complete workshop & service manual with electrical wiring diagrams for Nissan Qashqai (J10/J11 Series). It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

Nissan Qashqai (J10/J11 Series) service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

10,000+ pages, bookmarked, Searchable, Printable, high quality PDF

EXCERPT:
CLUTCH COVER
Check diaphragm spring lever claws for unevenness with the lever still on the vehicle. If they exceed the tolerance, adjust lever height using the diaphragm adjusting wrench.
Tolerance for diaphragm
spring lever unevenness
: Refer to CL-31,
“Clutch Cover”.
• Check clutch cover thrust ring for wear or breakage. If wear or breakage is found, replace clutch cover.
NOTE:
• Worn thrust ring will generate a beating noise when tapped at the rivet with a hammer.
• Broken thrust ring will make a clinking sound when cover is shaken up and down.
• If a trace of burn or discoloration is found on the clutch cover pressure plate to clutch disc contact surface, repair the surface with sandpaper. If surface is damaged or distorted, replace clutch cover.
…