Day: April 22, 2019

INSTANT DOWNLOAD (add to cart)

Toyota Matrix 2002-2014 Workshop Repair & Service Manual

Complete digital official shop manual contains service, maintenance, and troubleshooting information for the 2002-2014 Toyota Matrix. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual for 2002-2014 Toyota Matrix is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

MAKE: Toyota
MODEL: Matrix (a.k.a. Corola Matrix)
YEAR: 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012 2013 2014

EXCERPT:
1ZZ-FE ENGINE MECHANICAL – ENGINE UNIT EM–107
DISASSEMBLY
1. REMOVE OIL FILLER CAP SUB-ASSEMBLY
(a) Remove the oil filler cap from the cylinder head cover.
2. REMOVE OIL FILLER CAP GASKET
(a) Using a screwdriver, remove the gasket from the oil filler cap.
3. REMOVE VENTILATION VALVE SUB-ASSEMBLY
(a) Remove the ventilation valve from the cylinder head cover.
4. REMOVE SPARK PLUG
(a) Using a spark plug wrench, remove the 4 spark plugs.
5. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
(a) Remove the 9 bolts, 2 seal washers and 2 nuts, then remove the cylinder head cover.
6. REMOVE CYLINDER HEAD COVER GASKET
(a) Remove the gasket from the cylinder head cover.
7. REMOVE ENGINE MOUNTING BRACKET RH
(a) Remove the 3 bolts, then remove the engine mounting bracket RH.
8. REMOVE WATER PUMP ASSEMBLY
(a) Remove the 6 bolts, then remove the water pump.
9. REMOVE WATER PUMP O-RING
(a) Remove the O-ring from the timing chain cover.
10. REMOVE CRANKSHAFT PULLEY
(a) Set the No. 1 cylinder to the TDC/compression.
(1) Turn the crankshaft pulley until its groove and timing mark “0” of the timing chain cover are aligned.
(2) Check that the point marks of the camshaft timing gears are in a straight line on the timing chain cover surface as shown in the illustration.
If not, turn the crankshaft 1 revolution (360°) to align the marks as above.
(b) Using SST, remove the crankshaft pulley bolt.
SST 09960-10010 (09962-01000, 09963-01000)
(c) Remove the crankshaft pulley from the crankshaft.
11. REMOVE CHAIN TENSIONER ASSEMBLY NO.1
(a) Remove the 2 nuts, then remove the chain tensioner.
12. REMOVE TIMING CHAIN OR BELT COVER SUBASSEMBLY
(a) Remove the 10 bolts and 2 nuts.
(b) Remove the timing chain cover by prying the portions between the timing chain cover, cylinder head and cylinder block with a screwdriver.
NOTICE: Be careful not to damage the contact surfaces of the timing chain cover, cylinder head and cylinder block.
(c) Using a “TORX” socket wrench E5, remove the 3 stud bolts.
13. REMOVE TIMING CHAIN OR BELT COVER OIL SEAL
(a) Place the timing chain cover on wooden blocks.
(b) Using a screwdriver, remove the oil seal.
14. REMOVE CRANKSHAFT POSITION SENSOR PLATE NO.1
(a) Remove the crankshaft position sensor plate from the crankshaft.
…

INSTANT DOWNLOAD (add to cart)

Toyota Land Cruiser 1960-2016 Workshop Repair & Service Manual
Complete digital official shop manual contains service, maintenance, and troubleshooting information for the 1960-2016 Toyota Land Cruiser, Land Cruiser Prado. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual for Land Cruiser, Land Cruiser Prado is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

FILELIST: (4.6G~5G)
PZ471-Z0020-CA – Land Cruiser (UZJ100_FZJ100-105_HZJ105_HDJ100) Service Manuals.zip
Land Cruiser (GRJ200_UZJ200_VDJ200) Service Manuals.zip
Land Cruiser_Land Cruiser Prado (GRJ150, TRJ150-155, KDJ150-155, LJ150) Service Manual.zip
RM0800U – Land Cruiser 2008 Repair Manual.zip
36262E – Land Cruiser (60-, 70- Series) Heavy Duty Chassis & Body Repair Manual & EWD (’84-’90 Heavy Duty).pdf
RM035E – B, 3B, 11B, 13B, 13B-T Engine Repair Manual.pdf
RM184E – Land Cruiser Station Wagon (80- Series) Repair Manual for Chassis & Body & EWD.pdf
RM132E – B, 3B, 11B, 14B Engine Repair Manual.pdf
Land Cruiser Heavy-Duty (60-, 70- Series) Repair Manual for Chassis & Body & EWD.pdf
36044 – Land Cruiser (40-, 60- Series) Chassis & Body Repair Manual & EWD.pdf
MM001U – Maintenance Procedures (Land Cruiser 1986 Models).pdf
36044E – Land Cruiser (40-, 60- Series) Chassis & Body Repair Manual & EWD.pdf
00400-98077 – Land Cruiser (40-, 50- Series) Chassis & Body Repair Manual & EWD.pdf
RM315E – Land Cruiser (Hardtop, Canvas Top and Station Wagon) (80- Series) Repair Manual Supplement.pdf
EWDxxxU – Land Cruiser Station Wagon (80- Series) Electrical Wiring Diagram Supplement.pdf
98154 – Land Cruiser (40-, 50- Series) Chassis & Body Repair Manual & EWD.pdf
EWDxxxU – Land Cruiser, Land Cruiser Prado (90-, 95- Series) Electrical Wiring Diagram.pdf
EWD527E – Land Cruiser, Land Cruiser Prado (120-, 125- Series) Electrical Wiring Diagram.pdf
EWDxxxU – Land Cruiser (100-, 105- Series) Station Wagon Electrical Wiring Diagram.pdf
EM0800U – Land Cruiser 2008 Electrical Wiring Manual.zip
EWD595E – Land Cruiser, Land Cruiser Prado (120-, 125- Series) Electrical Wiring Diagram.pdf
Model application.txt
2011 Land Cruiser Service & Repair Manual
2014- Land Cruiser Service & Repair Manual
bonus_material
EWD601U – Land Cruiser Electrical Wiring Diagram 2005
Land Cruiser (70- Series) Repair Manual & EWD 1984-present
RM184E – Land Cruiser Station Wagon (80- Series) Repair Manual for Chassis & Body & EWD
RM1071U & EWD548U – Land Cruiser Repair Manual 1998-2007

EXCERPT:

STARTING – ACC CUT RELAY
ACC CUT RELAY
INSPECTION
1. REMOVE ACC CUT RELAY
Remove the relay box and ACC cut relay.
2. INSPECT ACC CUT RELAY CONTINUITY
(a) Using an ohmmeter, check that there is continuity between terminals 1 and 2.
If there is no continuity, replace the relay.
(b) Check that there is no continuity between terminals 3 and 5.
If there is continuity, replace the relay.
(c) Check that there is continuity between terminals 3 and 4.
If there is no continuity, replace the relay.
3. INSPECT ACC CUT RELAY OPERATION
(a) Apply battery positive voltage across terminals 1 and 2.
(b) Using an ohmmeter, check that there is no continuity between terminals 3 and 4.
If there is continuity, replace the relay.
(c) Using an ohmmeter, check that there is continuity between terminals 3 and 5.
If there is no continuity, replace the relay.
4. REINSTALL ACC CUT RELAY
…

INSTANT DOWNLOAD (add to cart)

Toyota iQ 2008-2015 Workshop Repair & Service Manual

Complete digital official shop manual contains service, maintenance, and troubleshooting information for the 2008-2015 Toyota/Scion iQ. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual for 2008-2015 Toyota/Scion iQ is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

MAKE: Toyota
MODEL: iQ (a.k.a. Scion iQ, Aston Martin Cygnet) (KGJ10 NUJ10 NGJ10 Series)
YEAR: 2008 2009 2010 2011 2012 2013 2014 2015

Repair Manual | New Car Features | Electrical Wiring Diagram | Body Repair | Service Data Sheet

EXCERPT:
ENTRY AND START SYSTEM (for Entry Function) > Driver Side Door Entry Lock and Unlock Functions do not Operate

for Preparation Click here

DESCRIPTION
When the driver door entry lock and unlock functions do not operate, one of the following may be malfunctioning: 1) power door lock control system; 2) front door outside handle assembly (for driver side); or 3) certification ECU.

WIRING DIAGRAM

INSPECTION PROCEDURE
NOTICE:
The entry and start system (for entry function) uses a multiplex communication system (LIN communication system) and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for entry function) after confirming that the communication system is functioning properly.
When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3, and turn a courtesy light switch on and off at 1.5-second intervals until communication between the tester and vehicle begins.

1.CHECK POWER DOOR LOCK OPERATION
When the door control switch on the master switch assembly is operated, check that the doors unlock and lock according to switch operation (Click here).
OK: Door locks operate normally.
NG: GO TO POWER DOOR LOCK CONTROL SYSTEM (PROCEED TO PROBLEM SYMPTOMS TABLE) (Click here)
OK =>

2.CHECK WAVE ENVIRONMENT
B216695E01
Bring the electrical key transmitter near the front door outside handle assembly (for driver side), and perform a driver door entry lock and unlock operation check.
NOTICE:
If the key is brought within 0.2 m (0.656 ft.) of the door outside handle assembly, communication is not possible.
HINT:
When the electrical key transmitter is brought near the front door outside handle assembly (for driver side), the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
If the operation is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
OK:
Entry functions operate normally.
…

INSTANT DOWNLOAD (add to cart)

Toyota Hilux 2005-2015 Workshop Repair & Service Manual

Complete digital official shop manual contains service, maintenance, and troubleshooting information for the Toyota Hilux 2005-2015. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your Hilux pickup like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual for Toyota Hilux 2005-2015 is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use this truck manual.

MAKE: Toyota
MODEL: Hilux (TGN 15/16/26, GGN 15/25, KUN 15/16/25/26)
YEAR: 2005 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015
FORMAT: PDF (ISO DISK IMAGE)
O.S.: Windows, Mac OS X, Linux…

Repair Manual
New Car Features
Electrical Wiring Diagram
Body Repair
Service Data Sheet

EXCERPT:

ENGINE COOLANT TEMPERATURE SENSOR > REMOVAL

1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

2. REMOVE V-BANK COVER
Remove the 2 nuts and the V-bank cover.

3. DISCONNECT NO. 2 VENTILATION HOSE

4. REMOVE AIR CLEANER ASSEMBLY
Disconnect the vacuum hose.
Disconnect the MAF meter connector.
Remove the 2 wire harness clamps.
Loosen the 2 hose clamps.
Remove the 2 bolts and air cleaner.

5. REMOVE THROTTLE BODY
Disconnect the throttle motor connector.
Remove the 4 bolts and throttle body.
Remove the gasket from the intake air surge tank.

6. REMOVE INTAKE AIR SURGE TANK
Disconnect the 2 water by-pass hose.
Disconnect the fuel vapor feed hose.
Disconnect the ventilation hose.
Disconnect the 2 VSV connectors.
Disconnect the throttle body with motor connector.
Separate the 3 wire harness clamps and hose clamp.
Remove the 2 bolts and throttle body bracket.
Remove the bolt and oil baffle plate.
Remove the 4 bolts and 2 surge tank stays.
Remove the 2 nuts.
Using an 8 mm socket hexagon wrench, remove the 4 bolts, intake air surge tank and gasket.

7. REMOVE INTAKE MANIFOLD
Disconnect the 6 fuel injector connectors.
Remove the 10 bolts, intake manifold and 2 gaskets.

8. REMOVE ENGINE COOLANT TEMPERATURE SENSOR
Disconnect the sensor connector.
Remove the sensor.
Remove the gasket from the sensor.
…

INSTANT DOWNLOAD (add to cart)

Toyota Pickup 1979-1995 Workshop Repair & Service Manual

Complete digital official shop manual contains service, maintenance, and troubleshooting information for the Toyota Pickup 1979-1995. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your Pickup like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual for Toyota Pickup 1979-1995 is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

EXCERPT:

1995 Toyota Pickup SR5
3.0L V6 VIN [V] 1995 Engines – 3.0L V6

ADJUSTMENT
VALVE CLEARANCE ADJUSTMENT

NOTE: Adjust valve clearance with engine cold.

1. Disconnect electrical connector from throttle position sensor. Release fuel pressure. See FUEL PRESSURE RELEASE under REMOVAL & INSTALLATION. Disconnect vacuum hoses and fuel line at fuel pressure regulator.
2. Disconnect PCV hose. Drain cooling system. Disconnect necessary coolant hoses, electrical connections and vacuum hoses for removal of air intake chamber located above valve cover. See Fig. 7.
3. Remove union bolt and gaskets at cold start injector. Power steering pump bracket may need to be removed for access to valve cover. If necessary, remove power steering pump with hoses attached and secure aside. Remove power steering pump bracket.
4. Disconnect hose from PAIR valve. See Fig. 7. Remove engine hanger and support for air intake chamber.
Remove EGR valve assembly. Remove bolts/nuts, air intake chamber and gasket. Disconnect electrical connectors for removal of wiring assembly, located across engine, in front of valve cover. Remove bolts and wiring assembly.
5. Remove spark plugs, valve covers and gaskets. Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Cylinder No. 1 is front cylinder on right side when viewed from rear of engine.
Ensure timing mark on crankshaft pulley aligns with “0” mark on timing belt cover.
6. Ensure valve lifters on cylinder No. 1 are loose and valve lifters on cylinder No. 4 are tight. If conditions are not as described, rotate crankshaft clockwise one complete revolution.
7. Using feeler gauge, measure and record valve clearance between valve lifter and camshaft on exhaust valve of cylinder No. 2 and intake valve of cylinder No. 6. See Fig. 1.
Fig. 1: Identifying Cylinder Numbers & Valve Locations
8. Rotate crankshaft clockwise an additional 120 degrees (1/3 revolution). Measure and record valve clearance on exhaust valve of cylinder No. 3 and intake valve of cylinder No. 1.
9. Rotate crankshaft clockwise an additional 120 degrees (1/3 revolution). Measure and record valve clearance on exhaust valve of cylinder No. 4 and intake valve of cylinder No. 2.
10. Rotate crankshaft clockwise an additional 120 degrees (1/3 revolution). Measure and record valve clearance on exhaust valve of cylinder No. 5 and intake valve of cylinder No. 3.
11. Rotate crankshaft clockwise an additional 120 degrees (1/3 revolution). Measure and record valve clearance on exhaust valve of cylinder No. 6 and intake valve of cylinder No. 4.
12. Rotate crankshaft clockwise an additional 120 degrees (1/3 revolution). Measure and record valve clearance on exhaust valve of cylinder No. 1 and intake valve of cylinder No. 5. Ensure valve clearance is within specification. See VALVE CLEARANCE SPECIFICATIONS table.
…