Day: April 22, 2019

INSTANT DOWNLOAD (add to cart)

Sterling 360 Trucks Factory Service & Shop Manual
Complete workshop & service manual with electrical wiring diagrams for Sterling 360 Trucks (Models COE30, COE40, COE45, COE50). It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Sterling 360 (Models COE30, COE40, COE45, COE50) service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

“STI-475-09 (08_08P).pdf”
Sterling 360 Workshop Manual (2009 Model Year)
Models: COE 30, COE 45, COE 50
STI-475-09 (08/08P); 2,525 pages

GROUP INDEX
GENERAL …00
MAINTENANCE SCHEDULE …01
ENGINE…11
LUBRICATION…12
FUEL AND ENGINE CONTROL…13A
COMMON RAIL SYSTEM…13EA
AUTO CRUISE AND VEHICLE SPEED LIMITATION SYSTEM…13EB
ECU REWRITE AND
PROGRAMMING…13ECU
COOLING…14
INTAKE AND EXHAUST …15
EMISSION CONTROL …17
AUTOMATIC TRANSMISSION…23
PROPELLER SHAFT …25
FRONT AXLE …26
REAR AXLE…27
WHEEL AND TIRE …31
FRONT SUSPENSION …33
REAR SUSPENSION…34
BRAKE…35A
ANTI-LOCK BRAKE SYSTEM (ABS) …35E
PARKING BRAKE …36
STEERING …37
BUMPER AND FRAME …41
CAB…42
DOOR…43
EXTERIOR …51
INTERIOR …52
ELECTRICAL…54
HEATER, AIR CONDITIONER,
AND VENTILATION…55
…

— — — — — — — — — — — — — — — — — — — — — — — — — — —

“STI-475-08 (11_07P).pdf”
Sterling 360 Workshop Manual (2008 Model Year)
Models: COE 30, COE 45, COE 50
STI-475-08 (11/07P); 2,515 pages

GROUP INDEX
GENERAL …00
MAINTENANCE SCHEDULE …01
ENGINE…11
LUBRICATION…12
FUEL AND ENGINE CONTROL…13A
COMMON RAIL SYSTEM…13EA
AUTO CRUISE AND VEHICLE SPEED LIMITATION SYSTEM…13EB
ECU REWRITE AND PROGRAMMING…13ECU
COOLING…14
INTAKE AND EXHAUST …15
EMISSION CONTROL …17
AUTOMATIC TRANSMISSION…23
PROPELLER SHAFT …25
FRONT AXLE …26
REAR AXLE…27
WHEEL AND TIRE …31
FRONT SUSPENSION …33
REAR SUSPENSION…34
BRAKE…35A
ANTI-LOCK BRAKE SYSTEM (ABS) …35E
PARKING BRAKE …36
STEERING …37
BUMPER AND FRAME …41
CAB…42
DOOR…43
EXTERIOR …51
INTERIOR …52
ELECTRICAL…54
HEATER, AIR CONDITIONER,
AND VENTILATION…55
…

— — — — — — — — — — — — — — — — — — — — — — — — — — —

“STI-475 (3_06P).pdf”
Sterling 360 Workshop Manual (2007 Model Year)
Models: COE 40, COE 45, COE 50
STI-475 (3/06P); 1,285 pages

GROUP INDEX
GENERAL …00
MAINTENANCE SCHEDULE …01
ENGINE…11
LUBRICATION…12
FUEL AND ENGINE CONTROL…13A
ELECTRONICALLY CONTROLLED FUEL SYSTEM …13E
COOLING…14
INTAKE AND EXHAUST …15
EMISSION CONTROL …17
CLUTCH…21
MANUAL TRANSMISSION …22
AUTOMATIC TRANSMISSION…23
PROPELLER SHAFT …25
FRONT AXLE …26
REAR AXLE…27
WHEEL AND TIRE …31
FRONT SUSPENSION …33
REAR SUSPENSION…34
BRAKE…35A
ANTI-LOCK BRAKE SYSTEM (ABS) …35E
PARKING BRAKE …36
STEERING …37
BUMPER AND FRAME …41
CAB…42
DOOR…43
EXTERIOR …51
INTERIOR …52
ELECTRICAL…54
HEATER, AIR CONDITIONER, AND VENTILATION…55
…

— — — — — — — — — — — — — — — — — — — — — — — — — — —

“Driver’s and Maintenance Manual (’07).pdf”
“Driver’s and Maintenance Manual (’08).pdf”
“Driver’s and Maintenance Manual (’09).pdf”

EXCERPT:
PISTONS, CONNECTING ROD AND CYLINDER LINERS
[Installation]
• Apply engine oil to the outside surface of the connecting rod bushing and the bushing fitting surface of the connecting rod.
• Fit collar B, the bushing, and collar A over the puller in the illustrated directions and lock this arrangement together with the nut.
• Align the oil holes in the connecting rod bushing and the connecting rod. Then, use a press to slowly apply a pressure of approximately 49 kN {11020 lbs, 5000 kgf} to the puller until the bushing is forced into place.
• After press-fitting the connecting rod bushing, measure the clearance between the piston pin and connecting rod bushing.
• If the measurement is less than the standard clearance range, ream the bushing.
Inspection: Connecting rod bend and twist
• Mount the connecting rod on the connecting rod aligner. Also mount the connecting rod bearings, piston pin, and connecting rod cap to create the same conditions as are expected when the connecting rod is mounted on a crankshaft. Tighten the bolts of the connecting rod bearing cap to a torque of 30 N·m {22 lbf·ft, 3.1 kgf·m}.
• Measure the extent of bend and twist in the connecting rod.
• If either measurement exceeds the specified limit, replace the connecting rod.
…

INSTANT DOWNLOAD (add to cart)

Subaru Tribeca 2006-2014 Workshop Repair & Service Manual
Complete digital official shop manual contains service, maintenance, and troubleshooting information for the 2006-2014 Subaru B9 Tribeca, Tribeca, Tribeca Limited, Tribeca Premium, Tribeca Touring. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual for 2006-2014 Subaru B9 Tribeca, Tribeca, Tribeca Limited, Tribeca Premium, Tribeca Touring is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

EXCERPT:
AT Main Case – AUTOMATIC TRANSMISSION
34.AT Main Case
A: REMOVAL
1) Remove the transmission assembly from vehicle body.
2) Pull out the torque converter assembly.
3) Remove the transmission harness connector from stay.
4) Disconnect the air breather hose.
5) Remove the oil charge pipe.
6) Remove the ATF filter inlet and outlet pipes.
7) Remove the extension case.
8) Remove the center differential carrier.
9) Remove the reduction driven gear.
10) Separate the converter case from the transmission case.
11) Remove the control valve body.
12) Remove the oil pump cover.
NOTE: The input clutch pack assembly and front sun gear assembly are also removed together.
13) Remove the needle bearing of the middle carrier assembly.
14) Remove the middle carrier assembly.
15) Remove the rear carrier assembly.
16) Remove the middle & rear sun gear assembly.
17) Remove the thrust needle bearing of high & low reverse clutch.
18) Remove the high & low reverse clutch assembly.
19) Remove the direct clutch assembly.
20) Remove the snap ring of reverse brake.
21) Remove the retaining plate.
22) Remove the leaf spring.
23) Take out the drive plate, driven plate and dish plate.
24) Remove the snap ring of the reverse brake spring retainer.
25) Remove the spring retainer.
26) Remove the return spring.
27) Apply compressed air.
28) Remove the reverse brake piston.
B: INSTALLATION
1) Install the reverse brake piston.
2) Install the return spring.
…

INSTANT DOWNLOAD (add to cart)

Subaru Alcyone SVX 1991-1997 Factory Service & Shop Manual
Complete workshop & service manual with electrical wiring diagrams for Subaru Alcyone SVX 1991-1997. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Subaru Alcyone SVX 1991-1997 service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

FILELIST: (1.7 G PDF)
SUBARU SVX 1992 SERVICE MANUAL.pdf
SUBARU SVX 1993 SERVICE MANUAL.pdf
SUBARU SVX 1994 SERVICE MANUAL.pdf
SUBARU SVX 1995 SERVICE MANUAL.pdf
SUBARU SVX 1996 SERVICE MANUAL.pdf
SUBARU SVX 1997 SERVICE MANUAL.pdf

EXCERPT:
2-7 [WSAO] SERVICE PROCEDURE
5. Collector Chamber and Intake
Manifold Assembly
A: REMOVAL
1) Release fuel pressure.
2) Remove collector cover.
3) Disconnect cruise control cable CD.
4) Disconnect accelerator cable®.
5) Loosen clamps which connect air intake duct to throttle body and mass air flow sensor.
6) Remove air intake duct.
7) Slide connector cover out from mass air flow sensor connector.
8) Disconnect connector from mass air flow sensor.
9) Remove clips on air cleaner upper cover.
10) Remove air cleaner element.
…

INSTANT DOWNLOAD (add to cart)

Complete workshop & service manual with electrical wiring diagrams for Subaru Sambar Truck & Van 1990-2012. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Subaru Sambar Truck & Van 1990-2012 service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

FILELIST:
00 – Table of Contents.pdf
01 – Vehicle Identification.pdf
02 – General Maintenance.pdf
03 – Suspension.pdf
04 – Steering.pdf
05 – Brake System.pdf
06 – Cooling System.pdf
07 – Intake Fuel Exhaust Systems.pdf
08 – Starting Charging Systems.pdf
09 – Engine Transmission Removal.pdf
10 – Engine Overhaul.pdf
11 – Transmission.pdf
12 – Wiring Diagrams.pdf
…

EXCERPT:
Subaru Sambar 660cc Truck & Van Factory Service Manual 1990-2006 (1990-2012 applicable)
V-KS3, V-KS4, V-KVS, V-KV4 2WD & 4WD AT-MT Models
Subaru Kei T11 Vehicles Series
Chapter 6
Engine Coolant & Cooling System
10. Coolant System Specifications and Capacities
11. Coolant System Components Diagram
12. Coolant System Radiator Components Diagrams
13. Engine Room Fan System
14. Troubleshooting Chart
15. Coolant Line Diagrams (Chassis Mount)
16. Water Pump
17. Engine Room Fan Circuit
18. Cooling Master Control Unit & Circuit
…

INSTANT DOWNLOAD (add to cart)

Complete workshop & service manual with electrical wiring diagrams for Subaru Leone/Loyale/DL/GL 1979-1994. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Subaru Leone/Loyale/DL/GL 1979-1994 service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

EXCERPT:
ENGINE LUBRICATION SYSTEM
(2) When ignition switch is turned ON, current flows through gauge section and heat wire of sender section. Because of low. point contact pressure, heat generated by low current allows bimetal to bend so that contact points open.
(3) Contact points (on sender side) open rapidly. Since temperature of bimetal (on gauge side) does not increase, bimetal hardly bends and the pointer does not move.
…