INSTANT DOWNLOAD (add to cart)
Complete workshop & service manual with electrical wiring diagrams for Caterpillar C7.1 Engines. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.
This Caterpillar C7.1 Engines service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.
MANUAL LIST:
KENR9226 – Troubleshooting (C7.1 Engines for Caterpillar Built Machines)
KENR8881 – Disassembly & Assembly (C7.1 Engines for Caterpillar Built Machines)
KENR9128 – Troubleshooting (C7.1 Engines for Caterpillar Built Machines)
KENR9240 – Specifications (C7.1 Engines for Caterpillar Built Machines)
KENR9241 – Systems Operation (C7.1 Engines for Caterpillar Built Machines)
KENR9241 – Testing & Adjusting (C7.1 Engines for Caterpillar Built Machines)
KENR9511 – Schematic (Marine Multi-Station Control System II Electrical System – Typical Dual Engine Installation)
RENR1377 – Systems Operation (Electric Protection System Energize-To-Run for Generator Set, Industrial & Marine Diesel Engines)
RENR1377 – Testing & Adjusting (Electric Protection System Energize-To-Run for Generator Set, Industrial & Marine Diesel Engines)
RENR7651 – Systems Operation (Marine Multi-Station Control System)
RENR7651 – Testing & Adjusting (Marine Multi-Station Control System)
RENR7651 – Troubleshooting (Marine Multi-Station Control System)
RENR7893 – Schematic (Marine Multi-Station Control System Electrical System – Typical Single Engine Installation)
RENR7929 – Schematic (Marine Multi-Station Control System Electrical System – Typical Dual Engine Installation)
SENR3130 – Torque Specifications
UENR3262 – Disassembly & Assembly – Seal Installation
LEBW4976 – Application & Installation Guide (Diesel Fuel & Diesel Fuel Systems).pdf
REHS1413 – Special Instruction – Installation of Cat Messenger for On-highway Engines.pdf
RENR1282 – Electronic PTO Installation & Application Guide (On-Highway Engines).pdf
SEBF9050 – Applied Failure Analysis – Engine Valve Failure Modes(1100, 1105).pdf
SENR2995 – Product Safety.pdf
SENR3130 – Specifications – Torque Specifications.pdf
SENR3130 – Specifications (Torque Specifications for All Caterpillar Products).pdf
SERT4052 – Service Training (Acert Technology for On-Highwayheavy Duty Engines).pdf
EXCERPT:
1. Release the pressure from the air system. Refer to the Original Equipment Manufactures (OEM) for the correct procedure.
2. Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, “Cooling System Coolant – Change” for the correct draining procedure.
If the engine is equipped with a hydraulic pump on the rear of the air compressor, remove the hydraulic pump. Refer to the OEM for the correct procedure.
3. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at the top center position on the compression stroke. Refer to Systems Operation, Testing and Adjusting, “Finding Top Center Position for No.1 Piston” for the correct procedure.
4. Note: The air compressor must be timed with the engine in order to minimize engine vibration.
…