Complete workshop & service manual with electrical wiring diagrams for Hitachi ZX 200-5G, 200LC-5G, 210H-5G, 210LCH-5G, 210K-5G, 210LCK-5G Hydraulic Excavator. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.
This Hitachi ZX 200-5G, 200LC-5G, 210H-5G, 210LCH-5G, 210K-5G, 210LCK-5G Hydraulic Excavator service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.
FILELIST:
TODCDEN00 – Hitachi ZX 200-5G, 200LC-5G, 210H-5G, 210LCH-5G, 210K-5G, 210LCK-5G Hydraulic Excavator Technical Manual (Operational Principle).pdf
TTDCDEN00 – Hitachi ZX 200-5G, 200LC-5G, 210H-5G, 210LCH-5G, 210K-5G, 210LCK-5G Hydraulic Excavator Technical Manual (Troubleshooting).pdf
TTDCDEN00 (attach to) – Hitachi ZX 200-5G, 330-5G class Excavator Electrical Wiring Digram.pdf
WDCDEN00 – Hitachi ZX 200-5G, 200LC-5G, 210H-5G, 210LCH-5G, 210K-5G, 210LCK-5G Hydraulic Excavator Workshop Manual.pdf
EXCERPT:
SECTION AND GROUP CONTENTS
WORKSHOP MANUAL
SECTION 1 GENERAL INFORMATION
Group 1 Precautions for Disassembling and Assembling
Group 2 Tightening
Group 3 Painting
Group 4 Bleeding Air
Group 5 Pressure Release Procedure
Group 6 Preparation
SECTION 2 MAINTENANCE STANDARD
Group 1 Upperstructure
Group 2 Undercarriage
Group 3 Front Attachment
SECTION 3 UPPERSTRUCTURE
Group 1 Cab
Group 2 Counterweight
Group 3 Main Frame
Group 4 Engine
Group 6 Hydraulic Oil Tank
Group 7 Fuel Tank
Group 8 Pump Device
Group 9 Control Valve
Group 10 Swing Device
Group 11 Pilot Valve
Group 12 Solenoid Valve
Group 13 Signal Control Valve
SECTION 4 UNDERCARRIAGE
Group 1 Swing Bearing
Group 2 Travel Device
Group 3 Center Joint
Group 4 Track Adjuster
Group 5 Upper and Lower Rollers
Group 6 Track
SECTION 5 FRONT ATTACHMENT
Group 1 Front Attachment
Group 2 Cylinder
…
SECTION 1 GENERAL
Group 5 Pressure Release Procedure
Hydraulic Circuit Pressure Release Procedure
Release any remaining pressure as follows before removing/installing the front attachment.
1. Set pilot shut-off lever (1) to the UNLOCK position.
2. Turn engine stop switch (2) ON.
NOTE: Perform step 1 and step 2, and set the key switch to the START position. Although the starter rotates, the engine does not start.
IMPORTANT: Battery will deplete. Operate the key switch for short period.
3. With the key switch set in the START position, operate the control lever in order to release any pressure in the hydraulic circuit 4 to 5 times.
4. Return pilot shut-off lever (1) to the LOCK position.
5. Turn engine stop switch (2) OFF.
…