JCB 3CX, 4CX, 214e, 214, 215, 217
Complete workshop & service manual with electrical wiring diagrams for JCB 2D, 2DS, 3, 3C, 3CS, 3CX, 3D, 4C, 4CN, 4CX, 5CX, 214e, 214, 214S, 215, 215E, 215S, 217, 217S, 700, 1400B, 1550B, 1700B & Variants Backhoe Loader. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.
This JCB 2D, 2DS, 3, 3C, 3CS, 3CX, 3D, 4C, 4CN, 4CX, 5CX, 214e, 214, 214S, 215, 215E, 215S, 217, 217S, 700, 1400B, 1550B, 1700B Backhoe Loaders service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.
FILELIST:745MB PDF
9802-8000 – JCB 3C, 3CX, 3D, 3DS, 4CT Backhoe Loader Parts Catalog.pdf
9803-1200 – Leyland 38 TD and 4/98NT Engine Service Workshop.pdf
9803-3250 – JCB 3C, 3CX, 3D, 4C, 4CN, 4CX, 214, 215, 217 (S.N. 290000&up) Excavator Loader Service Manual.pdf
9803-3257U – JCB 200 Series (3CX, 1400B, 1550B, 1700B) Backhoe Loader (SN 334,001&up) Service Manual.pdf
9803-3260 Issue 9 – JCB 3CX, 4CX & Variants Backhoe Loader Service Manual.pdf
9803-3270 – JCB 3CX, 4CX, 214, 215, 217 & Variants Backhoe Loader Service Manual.pdf
9803-3280 Issue 4 – JCB 3CX, 4CX, 214e, 214, 215, 217 & Variants Backhoe Loader Service Manual.pdf
9803-3280 Issue 9 – JCB 3CX, 4CX, 214e, 214, 215, 217 & Variants Backhoe Loader Service Manual.pdf
9803-3290 – JCB 3C, 3CX, 4CX Backhoe Loader Service Manual.pdf
9813-0250 – 3C, 3CX, 3CX Super, 4C, 4CX, 5CX, 214, 214S, 215, 215E, 215S, 217, 217S Backhoe Loader Service Manual.pdf
PCA 110M – BMC 3-cyl & 4-cyl Engien Parts Catalog.pdf
9803-3200 – JCB 2D, 2DS, 3, 3C, 3CS, 3D, 700 Excavator Loader Service Manual.pdf
JCB 2, 3, 3C & 4C (MK1) Operator’s Parts Book.pdf
JCB 2D-2DS-3-3C-3CS-3D-700 (MK2 & MK3 Range) (Manual Gearbox & Torque Converter) Excavator Loader Workshop Manual.pdf
EXCERPT:
Excavator Valve
Removal and Replacement Variable Flow
! WARNING
Make the machine safe before working underneath it. Park the machine on level ground, lower the arms. Apply the parking brake, put the transmission in neutral and stop the engine. Chock both sides of all four wheels.
Disconnect the battery, to prevent the engine being started while you are beneath the machine.
! DANGER
Hydraulic Pressure
Hydraulic fluid at system pressure can injure you. Before disconnecting or connecting hydraulic hoses, stop the engine and operate the controls to release pressure trapped in the hoses. Make sure the engine cannot be started while the hoses are open.
Removal
1 Sideshift the carriage to one side as shown (sideshift machines only). Lower the backhoe and loader end to the ground and stop the engine.
2 Operate the valve block levers back and forth to vent residual pressure.
3 Remove the hose guide A (this makes access to the valve block easier).
3 Remove clevis pins B to disconnect the control levers from the valve block spools.
4 Disconnect all hydraulic hoses from the valve block and plug all orifices to prevent ingress of dirt. Label each hose before disconnecting, this will ensure correct position when refitting.
5 Insert two M10 bolts through the eye end spools (three spools each end) as shown. Make sure the bolt has a retaining nut on each end. When the bolts are in place thread suitable slings around the bolts as shown.
! CAUTION
This component is heavy. Do not attempt to remove it unless its weight is held by a sling. Make sure that the sling is attached to a suitable lifting appliance.
7 Remove nuts C and lower the valve block to the ground.