Pages from Massey-Ferguson Tractors MF7400 (7485-7490-7495 Dyna-VT) Operator Instruction Book
FILELIST:
AGCO / Sisu Power 4th Generation Engines (33, 44, 49, 66, 74, 84 and 98) Workshop Manual (9806-4100).pdf
Massey-Ferguson Combine MF7200 (CEREA 7274, CEREA 7278) Operator’s Manual.pdf
Massey-Ferguson Hydraulic Planter Spreader MF 104 – 106 L Operator Manual / Parts Catalog.pdf
Massey-Ferguson MF 9695/9795 CE Operator’s Manual.pdf
Massey-Ferguson Seeders Spreader MF 300 Operator Manual.pdf
Massey-Ferguson Tractors 6200 Series (6235-6245-6255-6260-6265-6270-6280-6290) Operator Instruction Book.pdf
Massey-Ferguson Tractors MF2400 (MF2430 STD-GE, MF2435 STD-GE, MF2440 STD-GE) Operation and Maintenance Manual.pdf
Massey-Ferguson Tractors MF6100 (6110, 6120, 6130, 6140, 6150, 6160, 6170, 6180, 6190) Operator Instruction Book.pdf
Massey-Ferguson Tractors MF7400 (7485/7490/7495 Dyna-VT) Operator Instruction Book.pdf
SisuDiesel 320, 420, 620, 634 Engines Workshop Manual.pdf
SisuDiesel 320, 420, 620, 634 Service Manual (8366 40634 (9806-4550)).pdf
SisuDiesel 645 Engines Workshop Manual.pdf
SisuDiesel Citius Series (44, 49, 66, 74 and 84) Engines Workshop Manual (8370 62637).pdf
SisuDiesel Fortius Series (33, 44, 66, 74 and 84) Engines Workshop Manual (8366 62500).pdf
EXCERPT:
CONTENTS
Chapter 1
TRACTOR IDENTIFICATION
Chapter 2
INTRODUCTION – SAFETY INSTRUCTIONS AND WARRANTY
Chapter 3
INSTRUMENTS AND CONTROLS
Chapter 4
OPERATION
Chapter 5
SERVICING AND ADJUSTMENTS
Chapter 6
SPECIFICATIONS
Chapter 7
ACCESSORIES AND OPTIONS
Appendix
CONVERSION TABLES
Index
…
5.3 – OPERATOR SERVICE GUIDE
5.3.1 – Engine, fuel and cooling systems
1. Check/clean the dry air filter elements (section 5.9).
2. Check the radiator coolant level (section 5.10).
3. Clean the main radiator and all other cooler element fins (section 5.10).
4. Check the level of smoke emission from the exhaust.
5.3.2 – Electrical circuit and instruments
5. Check the condition of the battery and the electrolyte level.
6. Check the tightness of the battery connections and battery safety.
5.3.3 – Front axle and steering
7. Check the oil level in the front axle and final drives (4WD).
8. Lubricate the drive shaft/universal joints (4WD) (section 5.6).
9. Lubricate the steering pivots/suspended front axle.
10. Check the steering and wheel alignment (including tyre wear and damage).
5.3.4 – Transmission and hydraulics
11. Check the transmission/hydraulics oil level.
12. Lubricate the trumpet housing bearings (section 5.6).
13. Check the oil in the rear final drive units (according to model).
14. Check the “ZUIDBERG” front PTO oil level.
5.3.5 – Clutch
15. Check the clutch fluid level.
5.3.6 – General
16. Check and top up the windscreen washer bottle (section 5.7).
17. Lubricate all points with grease or oil as specified in the Operator Instruction Book (section 5.6).
…