Iveco EuroCargo_Tector 2002-2008
Complete digital official shop manual contains service, maintenance, and troubleshooting information for the 2002-2008 Iveco EuroCargo/Tector. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.
This manual for 2002-2008 Iveco EuroCargo/Tector is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.
MAKE: Iveco
— — — — — — — — —
MODEL: EuroCargo / Tector
— — — — — — — — —
YEAR: 2002, 2003, 2004, 2005, 2006, 2007, 2008
— — — — — — — — —
LANGUAGE: English/Italian
— — — — — — — — —
FORMAT: PDF (272 MB)
— — — — — — — — —
12-26T (603.93.391).pdf
EUROCARGO TECTOR 12 TO 26 t REPAIR MANUAL, 1,690 pages
12-26T (603.93.111).pdf
EUROCARGO TECTOR 12 TO 26 t REPAIR MANUAL, 886 pages
6-26T EWD (603.93.183) (IT).pdf
EUROCARGO TECTOR DA 6 A 26 t MANUALE PER LE RIPARAZIONI IMPIANTO ELETTRICO/ELETTRONICO, 192 pages
6-26T EWD (603.93.181) (EN).pdf
EUROCARGO TECTOR 6 TO 26 t REPAIR MANUAL ELECTRIC/ELECTRONIC SYSTEM, 192 pages
6-10T (EURO 4_5) (603.93.613) (IT).pdf
EUROCARGO EURO 4/5 DA 6 A 10 t MANUALE PER LE RIPARAZIONI, 828 pages
6-10T (603.93.381).pdf
EUROCARGO TECTOR 6 TO 10 t REPAIR MANUAL, 1,184 pages
6-10T (603.93.101).pdf
EUROCARGO TECTOR 6 TO 10 t REPAIR MANUAL, 648 pages
EXCERPT:
INDEX OF SECTIONS
Section
General Specifications 1
Engine 2
Clutch 3
Gearbox 4
Propeller shafts 5
Rear axles 6
Front Axles 7
Suspensions 8
Wheels and tyres 9
Steering 10
Pneumatic system — brakes 11
Body and chassis 12
Service plan 13
Electric/electronic system 14
Print 603.93.391 Base – October 2004
32 FRONT AXLE 5845 EUROCARGO TECTOR 12-26 t
520615 Steering knuckle pin bearing replacement
Figure 56
Steering knuckle bearing replacement (5) is made using for their disassembly and assembly beater’s elements (1-2-3) 99374527 and handle 99370007 (4).
Use element (1) and handle (4) to disassemble the sealing ring (8) and the roller bearings (6-7) on the upper side.
Use element (3) and handle (4) to disassemble the sealing ring (9) and the roller bearings (10-11) on the lower side.
Figure 57
Roller bearing assembly (7): use element (1 and 2) and handle (4).
Roller bearing assembly (6): use element (2) and handle (4).
Roller bearing assembly (8): use elements (3 and 2) and handle (4).
Roller bearing assembly (9): use element (2) and handle (4).
Figure 58
Use beater 99374171 (4) and handle 99370007 (3) to place sealing rings (2 and 5) in the steering knuckle (1).
Refitting
Figure 59
Set on the axle (2) the steering knuckle (3) and place the articulated pin (1).
Set tool 99374400 (4) on the steering knuckle (3) and fasten it by using the same lower cover lock screws (5), clamping them with the right torque.
Place the pin (1) in the axle conical housing, screwing the pressure screw (6) with a torque having 10 ÷ 11 daNm.
Remove tool 99374400 (4) from the steering knuckle (3).
Before placing the pin (1), it is necessary to check that the conical housing on the axle and the pin surface are perfectly cleaned and dry, in order to avoid oil layers which could foster the pin rotation in its place during its introduction.
…