Komatsu PC130-7 PC130-6K, PC150LGP-6K PC150-3, PC150LC-3 Excavator Repair & Service Manual (Searchable & Printable PDF)
Komatsu PC130-7 Shop Manual SAMPLE
Complete digital official shop manual contains service, maintenance, and troubleshooting information for the Komatsu PC130-7 PC130-6K, PC150LGP-6K PC150-3, PC150LC-3 Excavator. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.
This manual for Komatsu PC130-7 PC130-6K, PC150LGP-6K PC150-3, PC150LC-3 Excavator is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.
“Shop Manual (SEBM036301).pdf”
342 pages
PC130-7
70001 and up
“Shop Manual (EEBM001501).pdf”
730 pages
PC130-6K, PC150LGP-6K
K30001 and up, K35001 and up
“Operation & Maintenance (UEAM000602).pdf”
260 pages
PC130-6K, PC150LGP-6K HYDRAULIC EXCAVATOR
PC130-6K – K30001 and up, PC150LGP-6K – K35001 and up
“Shop Manual (SEBM021K0304).pdf”
559 pages
PC150-3, PC150LC-3 HYDRAULIC EXCAVATOR
3001 and up
Buy the best manual on the Internet from responsible merchant and get instant download without surprise.
INSTANT Delivery: A download link will be sent to you instantly after payment. Simply click on the link and save it to your computer. You can use this Manual as long as you wish with no restrictions.
PRINTABLE with Diagrams: Just print the manual out and start to work. You can also use the manual with your laptop in your garage.
Customer SATISFACTION: If there is any problem, just drop a quick email. Within hours the issue shall be taken care of.
REFUND Policy: We sell high quality products only. In case there is any problem with your purchase, a replacement link will be sent to you. If we are at fault, you get 100% refund.
EXCERPT:
Troubles which occur when solenoid power supply of governor and pump controller is
defective
~ The solenoid power supply (FB1-2) of the governor and pump controller is used by the controller to drive the solenoids and relays.
~ Accordingly, if the solenoid power supply is turned off, when the controller outputs the power to the solenoids or relays, the power is not supplied to any of the solenoids and relays and all or some of the following error codes are displayed simultaneously.
• [E213]: Disconnection in swing holding brake solenoid
• [E215]: Disconnection in 2-stage relief solenoid
• [E216]: Disconnection in travel speed shifting solenoid
• [E222]: Disconnection in LS-EPC solenoid
• [E223]: Disconnection in PC-EPC solenoid
~ If the above problems occur, check the related fuse (FB1-2) and inlet voltage of the governor and pump controller.
1) Disconnect connector C03 of the controller and connect a T-adapter to the wiring harness side.
2) Turn the starting switch ON.
3) Measure the voltage between each of pins (2) and (12) and each of pins (31), (32), and (33).
• Pins (2) and (3) are the power supply pins and pins (31), (32), and (33) are the ground pins.
• Pins (2) and (3) are the power supply and pins (31), (32), and (33) are the chassis ground.
• If the voltage is 20 – 30 V, it is normal.
~ Power supply connector (C03) of governor and pump controller