Day: October 5, 2017

BMW 550i, 550i GT, 550xi GT 2005-2010 – SAMPLE

Complete digital official shop manual contains service, maintenance, and troubleshooting information for the BMW 5-Series (E60/E61) 550i, 550i GT, 550xi GT 2005-2010. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual for BMW 5-Series (E60/E61) 550i, 550i GT, 550xi GT 2005-2010 is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

Buy the best manual on the Internet from responsible merchant and get instant download without surprise.

INSTANT Delivery: A download link will be sent to you instantly after payment. Simply click on the link and save it to your computer. You can use this Manual as long as you wish with no restrictions.

PRINTABLE with Diagrams: Just print the manual out and start to work. You can also use the manual with your laptop in your garage.

Customer SATISFACTION: If there is any problem, just drop a quick email. Within hours the issue shall be taken care of.

REFUND Policy: We sell high quality products only. In case there is any problem with your purchase, a replacement link will be sent to you. If we are at fault, you get 100% refund.

EXCERPT:
SUSPENSION
Steering and wheel alignment – Repair Instructions – 550i
ELECTRONIC CHASSIS ALIGNMENT
00 DANGER OF POISONING IF OIL IS INGESTED/ABSORBED THROUGH THE SKIN
Danger of poisoning!
Ingesting oil or absorbing through the skin may cause poisoning!
Possible symptoms are:

Headaches

Dizziness

Stomach aches

Vomiting

Diarrhoea

Cramps/fits

Unconsciousness
Protective measures/rules of conduct:
 Pour oil only into appropriately marked containers
 Do not pour oil into drinking vessels (drinks bottles, glasses, cups or mugs)
 Observe country-specific safety regulations
First aid measures:
 Do not induce vomiting.
If the person affected is still conscious, he/she must rinse out their mouth with water, drink plenty of water and consult a doctor immediately.
If the person affected is unconscious, do not administer anything by mouth, place the person in the recovery position and seek immediate medical attention.
00 RISK OF INJURY IF OIL COMES INTO CONTACT WITH EYES AND SKIN
Danger of injury!
Contact with eyes or skin may result in injury!
…

BMW 545i 2004-2005

Complete digital official shop manual contains service, maintenance, and troubleshooting information for the BMW 545i 2004-2005. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual for BMW 545i 2004-2005 is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

EXCERPT:
2004-05 ENGINE Engine Mechanical – Repair Instructions – 545i (4.4L) E60/N62
V/RIBBED BELT W/TENS. DEFLECT ELEMENT
11 28 010 REPLACING ALTERNATOR DRIVE BELT (N62/N62TU)
Special Tools Required:

11 3 340
Necessary Preliminary Tasks:

Remove fan clutch with fan impeller (E65/66). Refer to 11 52 020 REMOVING AND INSTALLING OR REPLACING FAN CLUTCH (N62).
Pretension belt tensioner slowly and carefully with a Torx socket as far as it will go and secure with special tool 11 3 340.
Remove drive belt.
NOTE: For Special Tool identification, see ENGINE- SPECIAL TOOLS – 5-SERIES (E60) .
NOTE: If the drive belt is to be reused: Mark direction of travel and reinstall drive belt in same direction of travel.
IMPORTANT: If contaminated with hydraulic fluid: Replace drive belt.
Fig. 232: Securing Belt Tensioner Using Pin
Put on the drive belt.
Remove special tool 11 3 340.
Installation:
Check that drive belt is correctly positioned on pulleys.
Fig. 233: Identifying Correctly Positioned Drive Belt
NOTE: For Special Tool identification, see AIR CONDITIONING & HEATING – SPECIAL TOOLS – (E60) .
11 28 050 REPLACING A/C COMPRESSOR DRIVE BELT (N62)
Special Tools Required:

64 1 040
Necessary Preliminary Tasks:

Remove alternator drive belt. Refer to 11 28 010 REPLACING ALTERNATOR DRIVE BELT
(N62/N62TU).

Remove engine splash guard.
Installation:
If reusing the drive belt, mark the direction of rotation and reinstall in the same direction.
Check drive belt for coolant and oil residues, replace if necessary.
IMPORTANT: If contaminated with hydraulic fluid: Replace drive belt.
Rotate engine at central bolt in direction of engine rotation.
At the same time, pull off drive belt (1) towards front in direction of arrow using a clean cloth (2).
Remove drive belt (1) towards front.
Fig. 234: Removing Drive Belt
Place drive belt (1) in position.
Clamp drive belt (1) with special tool 64 1 040 on belt pulley.
IMPORTANT: If contaminated with hydraulic fluid: Replace drive belt.
NOTE: With Dynamic Drive optional extra, detach bracket from A/C compressor (risk of damage).
…

BMW 540i 1994-2003

Complete digital official shop manual contains service, maintenance, and troubleshooting information for the BMW 540i 1994-2003. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual for BMW 540i 1994-2003 is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

EXCERPT:
1997-2003 ENGINE Engine Mechanical 4.4L – Repair Procedures – 540i/E39
V-RIBBED BELT WITH TENSIONER
11 28 010 REPLACING ALTERNATOR DRIVE BELT (M62)
NOTE: If the drive belt is to be subsequently reused:
Mark direction of travel and reinstall drive belt in same direction of travel.
Remove fan clutch with impeller, refer to 11 52 020 REMOVING AND INSTALLING OR REPLACING FAN COUPLING (M62).
Layout of drive belt.
Fig. 313: Layout Of Drive Belt
Slacken screws (1) and relieve tension on belt drive.
NOTE: Release screw (1 and 2) to remove complete belt tensioner.
Remove drive belt.
CAUTION: You must replace the drive belt if it is contaminated with hydraulic fluid.
Installation
Check drive belt for coolant and oil residue and replace if necessary.
Fig. 314: Slackening Screws From Tension On Belt Drive
Installation
Mount drive belt and check that it is correctly positioned on belt pulleys.
Pretension adjustable plate at hexagon head (1) up to end of elongated hole (2) and tighten down screws (3).
CAUTION: Screws (3) up to 9/98 M8 strength class 8.8 tightening torque 22 Nm.
Fig. 315: Aligning Pretension Adjustable Plate At Hexagon Head
Screws (3) from 9/98 with liquid-cooled alternator
M8 strength class 10.9 tightening torque 30 Nm.
11 28 050 REPLACING DRIVE BELT FOR A/C COMPRESSOR (M60 / M62 / M73)
NOTE: If the drive belt is to be reused, mark direction of travel and reinstall drive belt in same direction of rotation.
If necessary, remove splash guard.
Remove alternator drive belt, refer to 11 28 010 REPLACING ALTERNATOR DRIVE BELT (M62).
Loosen nuts (2 and 3) and remove compressor drive belt.
Installation
Check drive belt for coolant and oil residue and replace if necessary.
CAUTION: It is essential to replace drive belt if it comes into contact with hydraulic fluid.
…

BMW 535 1985-2016

Complete digital official shop manual contains service, maintenance, and troubleshooting information for the 1985-2016 BMW 535i, 535xi, 535is. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

535i: 1985-1989 1990-1993 2007-2016
535xi: 2008
535is: 1988

EXCERPT:
ENGINE Engine – Repair Instructions
HOUSING COVER
11 14 005 REPLACING FRONT CRANKSHAFT SEAL
Special tools required:

11 0 371

11 0 372

11 4 370

11 9 221

11 9 222

11 9 224

11 9 231

11 9 232

11 9 233

11 9 234
Necessary preliminary tasks:

Remove VIBRATION DAMPER.
IMPORTANT: Do not release central bolt.
Risk of damage
If the central bolt is released, the sprocket wheels of the timing chain and the oil pump will no longer be non-positively connected to the crankshaft. The camshafts to the crankshaft can warp.
The timing must be ADJUSTED again.
Fig. 66: Identifying Central Bolt
Turn back special tool 11 9 222.
Push special tool 11 9 221 onto crankshaft.
IMPORTANT: When screws are tightened down (special tool 11 9 224 ), crankshaft seal is
pressed inwards approx. 1 mm and thus slackened for subsequent removal.
Insert screws (special tool 11 9 224 ) and tighten down to approx. 20 Nm.
Fig. 67: Identifying Special Tool (11 9 222) (11 9 224) And (11 9 222)
Screw special tool 11 0 371 to 80 Nm into crankshaft seal.
Screw in spindle 11 0 372.
Release crankshaft seal from housing.
Repeat the operation several times if necessary.
Fig. 68: Screwing Special Tool (11 0 371) Into Crankshaft Seal
Carefully saw open crankshaft seal (1) at cutting line (2).
Remove crankshaft seal (1) from special tool 11 0 371.
Fig. 69: Identifying Crankshaft Seal And Cutting Line With Special Tool (11 0 371)
Installation note:
Clean sealing surface (1) and degrease thoroughly in area of housing partition.
Apply a light coat of oil to running surface (2) of crankshaft seal.
…

BMW 530(i,xi) 2001-2010

Complete digital official shop manual contains service, maintenance, and troubleshooting information for the 1994-1995.2001-2010 BMW 530i, 530xi, 530iT. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual for 1994-1995.2001-2010 BMW 530i, 530xi, 530iT is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

BMW 530(i,xi) 2001-2010
530i: 1994-1995 2001-2010
530iT: 1994-1995
530xi: 2006-2007

EXCERPT:
ENGINE Engine – Repair Instructions – N51, N52, N52K 6-Cylinder
36 VARIABLE CAMSHAFT TIMING
11 36 046 REMOVING AND INSTALLING/REPLACING INLET AND EXHAUST ADJUSTMENT
UNITS (N52)
Special tools required:

11 4 280

11 4 281

11 4 282

11 4 283
Necessary preliminary tasks:

Remove Cylinder Head Cover.
Fit special tool 11 4 283 with screws (1).
Fit special tool 11 4 281 on special tool 11 4 283.
Fig. 222: Identifying Special Tool (11 4 281), (11 4 282), (11 4 283) And Screws
Release chain tensioner (2).
For tightening torque refer to 11 31 5AZ in 11 31 CAMSHAFT (N52) .
IMPORTANT: To open central bolts on adjustment units and camshafts.
Fit special tool 11 4 280.
IMPORTANT: Special tool 11 4 282 must be fitted underneath on inlet camshaft.
Release central bolt on inlet/exhaust adjustment units (1).
For tightening torque refer to 11 36 1AZ in 11 36 VARIABLE CAMSHAFT CONTROL (N52) .
Fig. 223: Identifying Engine Central Bolt And Chain Tensioner
Detach exhaust adjustment unit (1) from exhaust camshaft.
Detach inlet adjustment unit (2) from inlet camshaft.
Installation:
To facilitate removal and installation of adjustment units, turn sensor gears at cutout downwards.
Fig. 224: Identifying Engine Inlet And Exhaust Adjustment Unit
IMPORTANT:
Danger of mixing up adjustment units.

Mixing up the adjustment units will result in engine damage.
The inlet and exhaust adjustment units are different.
VANOS is marked with AUS and EX for the exhaust camshaft.
VANOS is marked with EIN and IN for the inlet camshaft.
Sensor gears can be fitted alternatively.
Fig. 225: Identifying Inlet And Exhaust Camshaft Mark
Fit both adjustment units on camshafts.
The installation position of the adjustment units can be freely selected.
Insert screws (1).
For tightening torque refer to 11 36 1AZ in 11 36 VARIABLE CAMSHAFT CONTROL (N52) .
Fig. 226: Identifying Central Screw And Chain Tensioner
…