Month: May 2019

INSTANT DOWNLOAD (add to cart)

1,000+ total pages, bookmarked, Searchable, Printable, high quality PDF
87673890 NA – CX210B, CX240B Service Manual.pdf (954 pages)
87678603 (Replaces 87652081) – Case Models CX210B-CX230B Parts Catalog.pdf
87598354A – CX210B Hydraulic Schemcatic.pdf
87598360A – CX210B, CX240B Electrical Schematic.pdf (1,352 pages)

Complete workshop & service manual with electrical wiring diagrams for Case CX210B, CX240B Crawler Excavator. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Case CX210B, CX240B Crawler Excavator service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

EXCERPT:
BLEEDING AIR FROM THE MAIN HYDRAULIC SYSTEM COMPONENTS
IMPORTANT: After having bled the air from the components, shut down the engine for five minutes and then check that no air bubbles appear in the hydraulic fluid reservoir.
Hydraulic pump
CX160B
CX21OB/CX2408
CX290B
Using a solvent, clean the upper surface of the pump and the air bleed plug. Remove the air bleed plug.
Fill the pump with hydraulic fluid via that orifice. Install and tighten the air bleed plug.
Start the engine and run it at idle speed. Loosen the pump air bleed plug. Retighten the plug when fluid flows out of the orifice with no air bubbles. Carefully clean around the plug.
Attachment cylinders
Start the engine and run it at idle. Extend and retract all the cylinder rods four or five times without bringing them against the stops, then do the same again three or four times, but this time bringing the cylinder rods against the stops.
…

INSTANT DOWNLOAD (add to cart)

1,800 total pages, bookmarked, Searchable, Printable, high quality PDF
9-44110 – Pelles sur Chenilles CX180 MANUEL DE SERVICE (FR).pdf
9-44120 – CX180 Crawler Excavators Service Manual (EN).pdf
9-44120 – CX180 Crawler Excavators Service Manual (EN) (p1-p2).pdf
9-44130 – CX180 RAUPENBAGGER REPARATUR HANDBUCH (DE).pdf

Complete workshop & service manual with electrical wiring diagrams for Case CX180 Crawler Excavator. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Case CX180 Crawler Excavator service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

EXCERPT:
Apply clean grease on the O-ring (5) if this has not already been done and install the O-ring on the shaft (6). Install the hub (4) on the shaft and install a new
snap ring (3) to fasten the hub and shaft. Install a drain plug (1).
NOTE: Check the pitch of the retaining ports of the tension shock absorber yoke, see page 8.
STEP 7
Check for leaks to ensure that the idler wheel has been correctly reassembled and check for any damage which could give rise to leaks at seals and other components
…

INSTANT DOWNLOAD (add to cart)

1,902 total pages, bookmarked, Searchable, Printable, high quality PDF
7-28381 – Pelles sur Chenilles CX160 MANUEL DE SERVICE (FR).pdf
7-29061 – CX160 Crawler Excavators Service Manual (EN).pdf
7-29071 – CX160 RAUPENBAGGER REPARATUR HANDBUCH (DE).pdf

Complete workshop & service manual with electrical wiring diagrams for Case CX160 Crawler Excavator. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Case CX160 Crawler Excavator service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

EXCERPT:
Apply clean grease on the O-ring (5) if this has not already been done and install the O-ring on the shaft (6). Install the hub (4) on the shaft and install a new
snap ring (3) to fasten the hub and shaft. Install a drain plug (1).
NOTE: Check the pitch of the retaining ports of the tension shock absorber yoke, see page 8.
STEP 7
Check for leaks to ensure that the idler wheel has been correctly reassembled and check for any damage which could give rise to leaks at seals and other components
…

INSTANT DOWNLOAD (add to cart)

2,824 total pages, bookmarked, Searchable, Printable, high quality PDF
9-40470 – EXCAVADORA SOBRE ORUGAS CX135SR SCHEMATIC SET (ES).pdf
9-40480 – ESCAVATORE CINGOLATO CX135SR SCHEMATIC SET (IT).pdf
9-40631 – Pelles sur Chenilles CX135SR MANUEL DE SERVICE (FR).pdf
9-40641 – CX135SR Crawler Excavator Repair Manual (EN).pdf
9-40671 – CX135SR Raupenbagger REPARATUR HANDBUCH (DE).pdf

Complete workshop & service manual with electrical wiring diagrams for Case CX135SR Crawler Excavator. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Case CX135SR Crawler Excavator service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

EXCERPT:
Track tensioning mechanism Adjuster-recoil mechanism – Install (D.50.B.48.65 – F.10.A.15)
Check that the cylinder rod is inserted as far as possible into the cylinder barrel.
Move the tension cylinder into position.
Apply thread lock uid to the screws.
Support the tension cylinder whilst an assistant installs theat washers and screws to secure it.
Tighten the screws.
Next operation: Install the roller located under the tension cylinder, refer to Roller Lower roller – Install

Next operation: Steel track – Install (D.50.B.46 – F.10.A.15
…

INSTANT DOWNLOAD (add to cart)

4,074 total pages, bookmarked, Searchable, Printable, high quality PDF
7-27343 – Pelles sur Chenilles CX130 MANUEL DE SERVICE (FR).pdf
7-27353 – CX130 Crawler Excavators Service Manual (EN).pdf
7-27363 – CX130 RAUPENBAGGER REPARATUR HANDBUCH (DE).pdf

Complete workshop & service manual with electrical wiring diagrams for Case CX130 Crawler Excavator. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Case CX130 Crawler Excavator service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

EXCERPT:
NOTE: Carry out this step only if inspection reveals that the bushings (8) need to be replaced.
Using a hammer and a brass punch, drive the bushings (8) from the lower roller (1). Be careful not to damage the seal bore in the lower roller. Discard bushings.
If removed, install new bushings (8) in the lower roller (1) using a hydraulic press and a proper size rod.
STEP 1
Inspection
STEP 2
Clean all components with solvent.
STEP 3
Inspect the bushing surfaces on the shaft (6) for scoring, pitting, and other damage. Measure the diameter of the shaft at four opposing points.
Compare the values with the specifications, replace them if necessary.
STEP 4
Install an O-ring and a face seal metal bushing (5) in the seal bore on each side of the lower roller.
Inspect bushings (8) for wear and damage. Measure the inner diameter and width of the bushing.
Compare the values with the specifications, replace them if necessary.
STEP 5
Inspect the bore in each end cap and in the lower roller for damage that will result in leakage. Use new parts as required.
…