Month: August 2018

Pages from 9803-9410 – JCB 8025ZTS, 8026CTS, JS30, 8029CTS, 8030ZTS, 8035ZTS Service Manual

---

INSTANT DOWNLOAD

---

---

Complete workshop & service manual with electrical wiring diagrams for JCB Excavators 8025ZTS, 8026CTS, 8027Z, JS30, 8029CTS, 8030ZTS, 8032Z, 8035ZTS. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This JCB Excavators 8025ZTS, 8026CTS, 8027Z, JS30, 8029CTS, 8030ZTS, 8032Z, 8035ZTS service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

FILELIST:
9803-9300 – JCB Excavators 8027Z, 8032Z Service Manual.pdf
9803-9410 – JCB Excavators 8025ZTS, 8026CTS, JS30, 8029CTS, 8030ZTS, 8035ZTS Service Manual.pdf

EXCERPT:
Service Manual – 8025ZTS, 8026CTS, JS30, 8029CTS, 8030ZTS, 8035ZTS
Section 1 – General Information
Section 2 – Care and Safety
Section 3 – Maintenance
Section A – Attachments
Section B – Body and Framework
Section C – Electrics
Section D – Controls
Section E – Hydraulics
Section F – Gearboxes
Section J – Track and Running Gear
Section K – Engine
…
Servo Hand Controllers
Introduction
This section deals with the Remote Control Valve which provides pilot pressure for the hydraulic control valve and electrical switching to flow-control solenoids.
The remote control valve is a pressure reduction valve used to control the pilot pressure operated system. Four pressure reduction valves used to control the pilot pressure are located in the main housing. Direction of the output pilot pressure is controlled by selective movement of the control lever. The valves and control levers are mounted in the arm rests on both sides of the operator’s seat.
…

---

INSTANT DOWNLOAD

---

---

Pages from 9803-9600 – JCB Excavators 8020 Service Manual

Complete workshop & service manual with electrical wiring diagrams for JCB Excavators 8013, 8014, 8015, 8016, 8017, 8018, 8020, 801 gravemaster. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This JCB Excavators 8013, 8014, 8015, 8016, 8017, 8018, 8020, 801 gravemaster service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

FILELIST:
9803-3105 – JCB Excavators 8013, 8015, 8017, 8018, 801 gravemaster Service Manual.pdf
9803-9350 – JCB Excavators 8014, 8016, 8018, 8020 Service Manual.pdf
9803-9600 – JCB Excavators 8020 Service Manual.pdf

EXCERPT:
General Information
Section 1 – General Information
Section 2 – Care and Safety
Section 3 – Maintenance
Section A – Attachments
Section B – Body and Framework
Section C – Electrics
Section D – Controls
Section E – Hydraulics
Section F – Gearboxes
Section J – Track and Running Gear
Section K – Engine
…
Removal and Replacement
Removal
1 Park the machine on firm level ground. Lower the excavator and dozer to the ground.
2 Stop the engine and remove the starter key.
3 Vent the hydraulic system.
Fig 3.
4 Remove arm rest plug A and undo screw C.
5 Remove armrest B.
6 Remove clamping ring D.
Fig 4.
7 Undo screws E and raise the hand controller F from the housing.
…

Pages from 9803-8060 – JCB Fastrac 7000 Series (7170, 7200, 7230 P-TRONIC) Service Manual

Complete workshop & service manual with electrical wiring diagrams for JCB Fastrac 7000 Series (7170, 7200, 7230 P-TRONIC). It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This JCB Fastrac 7000 Series (7170, 7200, 7230 P-TRONIC) service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

9803-8060 – JCB Fastrac 7000 Series (7170, 7200, 7230 P-TRONIC) Service Manual.pdf

EXCERPT:
Service Manual
JCB 7000 Series Fastrac
Section 1 – General Information
Section 2 – Care and Safety
Section 3 – Maintenance
Section A – Optional Equipment
Section B – Body and Framework
Section C – Electrics
Section E – Hydraulics
Section F – Transmission
Section G – Brakes
Section H – Steering
Section S – Suspension
Section T – Engine
…
Dismantling and Assembly
The numerical sequence shown on the illustration is intended as a guide to dismantling K Fig 33. ( T E-25).
Before removing and dismantling the pump, check the flow and pressure for each section of the pump (see Section H, Steering and Section S, Suspension – Technical Data).
If the values are low, renewal of components such as gears, bearings and housings will not effect a permanent cure. If the pump output is satisfactory but there is external leakage, dismantle the pump for re-sealing only.
Note: If the steering flow rate is low, make sure that there is no dirt in the end cover 12 and that the spool 10 moves freely. The size of washer 9 controls the steering flow rate (see Technical Information Bulletin 10/183).
For assembly the sequence should be reversed.
When Dismantling
…

Pages from 9813-1200 – JCB Fastrac 3200, 3230 Tier 4 Service Manual

Complete workshop & service manual with electrical wiring diagrams for JCB Fastrac 3170, 3170 Plus, 3190, 3190 Plus, 3200, 3200 Plus, 3220, 3220 Plus, 3230, 3230 Plus. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This JCB Fastrac 3170, 3170 Plus, 3190, 3190 Plus, 3200, 3200 Plus, 3220, 3220 Plus, 3230, 3230 Plus service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

FILELIST:
9803-8030 – JCB Fastrac 3170, 3170 Plus, 3190, 3190 Plus, 3200, 3200 Plus, 3220, 3220 Plus, 3230, 3230 Plus Service Manual.pdf
9813-1200 – JCB Fastrac 3200 / 3230 Tier 4 Service Manual.pdf

EXCERPT:
Service Manual
Fastrac 3200 / 3230 Tier 4
Section 1 – General Information
Section 2 – Care and Safety
Section 3 – Routine Maintenance
Section A – Hitches and Attachments
Section B – Body and Framework
Section C – Electrics
Section E – Hydraulics
Section F – Transmission
Section G – Brakes
Section H – Steering
Section S – Suspension
Section T – Engine
…
Brake SYSTEM (ABS with Hill Hold)
Introduction
This topic contains information about a machine SYSTEM. The system has some devices that connect either
mechanically, hydraulically or electrically. Make sure you are referring to the correct system.
Descriptions and procedures relate to the system and not the individual devices.
This topic is intended to help you understand what the system does and how it works. Where applicable it also includes procedures such as removal and replacement and dismantle and assemble.
K Technical Data ( T G2-2)
K Service Tools ( T G2-3)
K Operation Overview ( T G2-4)
K Air Pipes – Colour Codes ( T G2-6)
K Air Compression ( T G2-7)
K Front Brake Circuit ( T G2-7)
K Rear Brake Circuit ( T G2-7)
K Trailer / Parking Brake Circuit ( T G2-7)
K Parking Brake Circuit ( T G2-8)
K Hydraulic Trailer Brakes (if fitted) ( T G2-8)
K Tractor ABS ( T G2-9)
K Fault Finding ( T G2-12)
K Bleeding ( T G2-15)
…

Pages from 9803-9970 – JCB 3000 XTRA Series Fastrac Service Manual

Complete workshop & service manual with electrical wiring diagrams for JCB 3000 XTRA Series Fastrac. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This JCB 3000 XTRA Series Fastrac service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

9803-9970 – JCB 3000 XTRA Series Fastrac Service Manual.pdf

EXCERPT:
Service Manual
3000 XTRA Series Fastrac
Section 1 – General Information
Section 2 – Care and Safety
Section 3 – Routine Maintenance
Section A – Hitches and Attachments
Section C – Electrics
Section E – Hydraulics
Section F – Transmission
Section G – Brakes
Section H – Steering
Section S – Suspension
Section T – Engine
…
Transmission
Checking the Transmission Oil Level
1 Park the machine on firm, level ground. Engage the park brake. Lower the equipment. Stop the engine.
2 Check that oil is at the top mark on dipstick X. Add recommended oil, if necessary, at filler Y. K Fluids, Lubricants and Capacities, Fuel ( T 11)
After topping up, run the engine for 1 minute, then stop the engine and allow to stand for 2 minutes before re-checking the level.
Note: Do not overfill as this would cause oil to be forced past the oil seals and out of the gearbox.
…