Month: August 2018

Pages from Massey-Ferguson Tractors MF7400 (7485-7490-7495 Dyna-VT) Operator Instruction Book

FILELIST:
AGCO / Sisu Power 4th Generation Engines (33, 44, 49, 66, 74, 84 and 98) Workshop Manual (9806-4100).pdf
Massey-Ferguson Combine MF7200 (CEREA 7274, CEREA 7278) Operator’s Manual.pdf
Massey-Ferguson Hydraulic Planter Spreader MF 104 – 106 L Operator Manual / Parts Catalog.pdf
Massey-Ferguson MF 9695/9795 CE Operator’s Manual.pdf
Massey-Ferguson Seeders Spreader MF 300 Operator Manual.pdf
Massey-Ferguson Tractors 6200 Series (6235-6245-6255-6260-6265-6270-6280-6290) Operator Instruction Book.pdf
Massey-Ferguson Tractors MF2400 (MF2430 STD-GE, MF2435 STD-GE, MF2440 STD-GE) Operation and Maintenance Manual.pdf
Massey-Ferguson Tractors MF6100 (6110, 6120, 6130, 6140, 6150, 6160, 6170, 6180, 6190) Operator Instruction Book.pdf
Massey-Ferguson Tractors MF7400 (7485/7490/7495 Dyna-VT) Operator Instruction Book.pdf
SisuDiesel 320, 420, 620, 634 Engines Workshop Manual.pdf
SisuDiesel 320, 420, 620, 634 Service Manual (8366 40634 (9806-4550)).pdf
SisuDiesel 645 Engines Workshop Manual.pdf
SisuDiesel Citius Series (44, 49, 66, 74 and 84) Engines Workshop Manual (8370 62637).pdf
SisuDiesel Fortius Series (33, 44, 66, 74 and 84) Engines Workshop Manual (8366 62500).pdf

EXCERPT:
CONTENTS
Chapter 1
TRACTOR IDENTIFICATION
Chapter 2
INTRODUCTION – SAFETY INSTRUCTIONS AND WARRANTY
Chapter 3
INSTRUMENTS AND CONTROLS
Chapter 4
OPERATION
Chapter 5
SERVICING AND ADJUSTMENTS
Chapter 6
SPECIFICATIONS
Chapter 7
ACCESSORIES AND OPTIONS
Appendix
CONVERSION TABLES
Index
…
5.3 – OPERATOR SERVICE GUIDE
5.3.1 – Engine, fuel and cooling systems
1. Check/clean the dry air filter elements (section 5.9).
2. Check the radiator coolant level (section 5.10).
3. Clean the main radiator and all other cooler element fins (section 5.10).
4. Check the level of smoke emission from the exhaust.
5.3.2 – Electrical circuit and instruments
5. Check the condition of the battery and the electrolyte level.
6. Check the tightness of the battery connections and battery safety.
5.3.3 – Front axle and steering
7. Check the oil level in the front axle and final drives (4WD).
8. Lubricate the drive shaft/universal joints (4WD) (section 5.6).
9. Lubricate the steering pivots/suspended front axle.
10. Check the steering and wheel alignment (including tyre wear and damage).
5.3.4 – Transmission and hydraulics
11. Check the transmission/hydraulics oil level.
12. Lubricate the trumpet housing bearings (section 5.6).
13. Check the oil in the rear final drive units (according to model).
14. Check the “ZUIDBERG” front PTO oil level.
5.3.5 – Clutch
15. Check the clutch fluid level.
5.3.6 – General
16. Check and top up the windscreen washer bottle (section 5.7).
17. Lubricate all points with grease or oil as specified in the Operator Instruction Book (section 5.6).
…

ACRO 8200-Series

---

INSTANT DOWNLOAD

---

Complete workshop & service manual with electrical wiring diagrams for AGCO / Massey Ferguson 8200 Series Tractors (8210, 8220, 8220 Heavy Duty, 8220 Xtra, 8240, 8240 Xtra, 8245, 8245 Heavy Duty, 8250, 8250 Xtra, 8260, 8260 Xtra, 8270, 8270 Xtra, 8280, 8280 Xtra). It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This AGCO / Massey Ferguson 8200 Series Tractors service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

Workshop Service Manual for AGCO / Massey Ferguson 8200 Series Tractors (8210, 8220, 8220 Heavy Duty, 8220 Xtra, 8240, 8240 Xtra, 8245, 8245 Heavy Duty, 8250, 8250 Xtra, 8260, 8260 Xtra, 8270, 8270 Xtra, 8280, 8280 Xtra) (Three Point Power, Wintest User Guide)

N° 3378177 M1; May 2001; 2,335 pages

EXCERPT:
8 . FRONT AXLE
8 A01 GENERALITY – CARRARO FRONT AXLE
8 B01 DANA FINAL DRIVE UNITS
8 B02 ZF FINAL DRIVE UNITS
8 B03 CARRARO FINAL DRIVE UNITS
8 C01 DANA DIFFERENTIAL
8 C02 ZF DIFFERENTIAL
8 C03 CARRARO DIFFERENTIAL
8 D01 2 WD FRONT AXLE
8 E01 STEERING COLUMN
8 F01 BEARINGS AND TRANSMISSION SHAFTS (DANA FRONT AXLE)
8 F02 BEARINGS AND TRANSMISSION SHAFTS (ZF FRONT AXLE)
8 F03 BEARINGS AND TRANSMISSION SHAFTS (CARRARO FRONT AXLE)
8 G01 4WD CLUTCH
8 G02 CARRARO SUSPENSION
8 I01 CARRARO TROUBLESHOOTING
…
Front axle – Generality
The axle described in this manual, designed and manufactured following the customer’s requests, consists of a beam casing, housing the differential in the middle and a wheel hub unit at each end.
The differential, type “Limited Slip”, is supported by two bearings mounted on a suitable structure allowing the bevel gear set to be adjusted.
The ring bevel gear is adjusted by means of two ring nuts located opposite each other.
The position of the bevel pinion, supported by two bearings, is adjusted by inserting adjusting shims.
The wheel hubs containing the epicyclic reduction gears are supported by two tapered roller bearings and are powered by a hydraulically-operated steering unit.
The axle is equipped with hydropneumatic shock-absorbing suspension system (Carraro patent), electronically controlled, ensuring the constant contact of the tyres with the ground in any operating conditions.
…

---

INSTANT DOWNLOAD

---

Pages from AGCO-Massey-Ferguson Tractor Series 8100 (Model MF 8110-8120-8130-8140-8150-8160) Workshop Service Manual

Complete workshop & service manual with electrical wiring diagrams for AGCO/Massey-Ferguson Tractor Series 8100 (Model MF 8110, 8120, 8130, 8140, 8150, 8160). It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This AGCO/Massey-Ferguson Tractor Series 8100 (Model MF 8110/8120/8130/8140/8150/8160) service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

AGCO/Massey-Ferguson Tractor Series 8100 (Model MF 8110/8120/8130/8140/8150/8160) Workshop Service Manual.pdf

EXCERPT:
TABLE OF CONTENTS
WORKSHOP SERVICE MANUAL
1 Introduction – Specifications
2 Splitting the tractor
3 Engine and equipment
4 Clutch
5 Gearbox
6 Rear axle
7 Power Take Off
8 Front axle 2 and 4WD
9 Hydraulics
10 Electrical equipment
11 Electronics
12 Cab and Equipment
…
Clutch 4A01.7
D. Removing, refitting, and shimming the clutch
Removal
24.Split the tractor between the engine and the gearbox (see section 2801 ).
25. Drain the oil from the gearbox and rear axle.
26. If the tractor is fitted with the chassis reinforce- ments, remove the right-hand side.
27. Remove the tube (17).
28. Remove the cover plate (1 0).
Repeat procedure 12.
29. Remove the tube (20).
30. Remove the union (72) and tubes (70) and (65).
…

Pages from AGCO-Massey-Ferguson Tractor Series 6400 (Model MF 6445-6455-6460-6465-6470-6475-6480-6485-6490-6495-6497-6499) Workshop Service Manual

Complete workshop & service manual with electrical wiring diagrams for AGCO/Massey-Ferguson Tractor Series 6400 (Model MF 6445/6455/6460/6465/6470/6475/6480/6485/6490/6495/6497/6499). It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This AGCO/Massey-Ferguson Tractor Series 6400 (Model MF 6445, 6455, 6460, 6465, 6470, 6475, 6480, 6485, 6490, 6495, 6497, 6499) service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

FILELIST:
3378818M1 – AGCO/Massey-Ferguson Tractor 6400 Series Tractors (6497/6499) Operator Instruction Book.pdf
4315415M1 – AGCO/Massey-Ferguson Tractor 6400 Series Tractors (6465/6475/6480) Operator Instruction Book.pdf
AGCO/Massey-Ferguson Tractor Series 6400 (Model MF 6445/6455/6460/6465/6470/6475/6480/6485/6490/6495/6497/6499) Workshop Service Manual.pdf

EXCERPT:
Twin flow load sensing right-hand hydraulic cover
E . Disassembling and reassembling the cover Disassembly
61. Take off the cover (see § C).
62. Place the cover (1) in a vice fitted with plastic jaws. On the outside face (Fig. 1)
63. Mark the locations and types of solenoid valves (7) to (11) and remove them.
64. Mark the location of the switches (6) (19) and remove them.
65. Remove the engine speed sensor.
66. Remove the hydraulic unions and plugs, fitted according to the version.
67. Remove the diagnostics connectors.
Note: On tractors not fitted with trailer braking, if necessary, remove the cover plate (3) (see section 09B03).
68. Take off the high pressure valve (3).
On the inside face (Fig. 2)
69. Take out the screws (31) and remove the inlet manifold (40), seal (24) and pipe (42). Remove seals (41).
Removing the drive pinion
70. Unscrew nut (27). Take off washer (28), pinion (29) and key (30).
71. Take off the pump (see § F).
Reassembly
72. Clean the cover mating faces.
73. Check that no channels (low and high flow rate) are blocked. Check for the presence of the rivets ensuring oil tightness at the end of each channel.
On the inside face (Fig. 2)
74. Refit the pump (see § F).
Refitting the drive pinion
75. Position the key (30). Fit the pinion (29) on the shaft while ensuring that the key is correctly engaged.
Fit washer (28).
76. Smear the nut (27) with Loctite 241 and tighten to a torque of 50 – 60 Nm.
77. Replace the O’rings (41) on the pipe (42).
78. Refit the seal (24), the pipe and the inlet manifold
(40). Refit and moderately tighten the screws (31).
…

Pages from AGCO-Massey-Ferguson Tractor Series 5400 (Model MF 5425-5435-5445-5455-5460-5460SA-5465-5470-5470SA-5475SA) Workshop Service Manual

Complete workshop & service manual with electrical wiring diagrams for Massey-Ferguson Tractor Series 5400 (Model MF 5425, 5435, 5445, 5455, 5460, 5460SA, 5465, 5470, 5470SA, 5475SA). It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Massey-Ferguson Tractor Series 5400 (Model MF 5425/5435/5445/5455/5460/5460SA/5465/5470/5470SA/5475SA) service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

FILELIST:
AGCO/Massey-Ferguson Tractor Series 5400 (Model MF 5425/5435/5445/5455/5460/5460SA/5465/5470/5470SA/5475SA) Workshop Service Manual.pdf
AGCO/Massey-Ferguson Tractor Series 5400 (Models 5425-5435-5445-5455-5460-5465) Operator Instruction Book.pdf

EXCERPT:
DANA – Differential
E . Removing the differential unit
10. Place the housing (7) in a vice fitted with soft jaws (Fig. 4).
11. Take out the screw (30) and its lock (31) (Fig. 4).
12. Take off the spline nut (32) using the special makeshift wrench (see § Q).
13. Take out the four screws (42).
14. Take off the half-bearings (43) (Fig. 4).
CAUTION: Take care not to release the spring (17) when releasing the differential lock half bearing. The washer (21) that seats the spring should stay in the housing.
15. Remove the differential assembly complete with cones (33) and cups (29) (Fig. 5). Separate the cups from the cones. Remove the shim(s) (22) used to
adjust the backlash.
NOTE: Pair up the bearing cones and cups in they are to be re-used.
…