Month: August 2018

Pages from AGCO-Massey-Ferguson Tractor Series 3600 (Model MF 3615-3625-3635-3645) Workshop Service Manual

Complete workshop & service manual with electrical wiring diagrams for AGCO/Massey-Ferguson Tractor Series 3000/3100/3600 (3050, 3060, 3065, 3070, 3080, 3095, 3115, 3125, 3120, 3140, 3615, 3625, 3635, 3645). It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This AGCO/Massey-Ferguson Tractor Series 3000/3100/3600 service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

FILELIST:
1646915 M1 – AGCO/Massey-Ferguson Tractor Series 3000/3100 (Model MF 3050/3060/3065/3070/3080/3095/3115/3125/3120/3140) Workshop Service Manual.pdf
AGCO/Massey-Ferguson Tractor Series 3600 (Model MF 3615/3625/3635/3645) Workshop Service Manual.pdf

EXCERPT:
Hydraulic Lift
Section 2
Table of Contents
SPECIFICATIONS . . . 248
TECHNICAL FEATURES . . . 248
DIMENSIONAL FEATURES . . 248
CALIBRATION SETTINGS OF CONTROL VALVE . . . 248
DIAGRAM . . . 249
CIRCUIT DIAGRAM OF HYDRAULIC LIFTING DEVICE . . . 250
FUNCTIONING OF CONTROL VALVE . . 251
NEUTRAL PHASE . . 251
DELIVERY PHASE . . 252
DISCHARGE PHASE . . 253
HOW THE INTERNAL LEVERAGE SYSTEM FUNCTIONS . . 254
FUNCTIONING WITH POSITION CONTROL (FIG. PAGE 5.2) . . . 254
FUNCTIONING OF DRAFT CONTROL (FIG. PAGE 5.2 – 5.4) . . 256
COMBINED FUNCTIONING OF POSITION AND DRAFT CONTROL (FIG. PAGE 5.2-5.4) . . . 258
USE OF CONTROL LEVERS . . 259
POSITION CONTROL (LEVER 1) . . 259
DRAFT CONTROL (LEVER 2) . . . 259
COMBINED OPERATION FOR POSITION AND DRAFT CONTROL . . . 259
ADJUSTMENT OF CONTROL VALVE SENSITIVITY . . . 260
FUNCTIONING OF THE SENSITIVITY OF THE CONTROL VALVE . . . 260
ADJUSTMENT OF POSITION CONTROL LEVER . . . 262
ADJUSTMENT OF DRAFT CONTROL LEVER . . 263
CONTROL OF ASSEMBLY OF REACTION SPRING . . . 264
MEASUREMENT CONTROL OF PUSH ROD . . . 265
DIAGNOSTIC . . 266
…

Pages from 1856274 M1 – Massey-Ferguson MF 600 Series Workshop Service Manual

Complete workshop & service manual with electrical wiring diagrams for Massey-Ferguson MF 600-Series. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Massey-Ferguson MF 600-Series service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

1856274 M1 – Massey-Ferguson MF 600 Series Workshop Service Manual.pdf

EXCERPT:
CLUTCH RELEASE MECHANISM
GEARBOX TYPES A, B, C, D, E
Special Tools: MS 2700 Rail Trolley
Removal 58-04–11
1. Split the tractor between the engine and the transmission, Part 3A.
2. Remove the two springs.
3. Slide the carrier and release bearing off the input housing.
4. Remove the locking wire and locking peg.
5. Remove the circlip.
6. Remove the shaft.
7. Remove the clutch release fork.
8. Press the release bearing off the carrier.
Refitment
9. Reverse procedures 1 to 8, except:
(a) Lightly lubricate the input shaft splines and the release bearing carrier bore, with special grease Mobilgrease Super.
(b) Ensure that the locking peg locates in the hole in the shaft.
…

Pages from Massey-Ferguson MF230-MF235-MF240-MF245-MF250 Shop Manual

Complete workshop & service manual with electrical wiring diagrams for Massey-Ferguson Tractors MF230-MF235-MF240-MF245-MF250. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Massey-Ferguson Tractors MF230-MF235-MF240-MF245-MF250 service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

Massey-Ferguson Tractors MF230-MF235-MF240-MF245-MF250 Shop Manual.pdf

EXCERPT:
HYDROSTATIC STEERING SYSTEM
This section covers the steering system used on MF2 35 Orchard models arid all MF245 models except Vineyard.
LUBRICATION AND BLEEDING
All Models So Equipped
18. The hydrostatic steering hand pump and steering cylinder assembly are lubricated by the operating fluid.
Massey-Ferguson Pe rmatran III Oil is recommended. The system is self bleeding, but steering should be cycled and reservoir refilled as often as necessary until level stops dropping.
SYSTEM OPERATING PRESSURE AND RELIEF VALUE
All Models So Equipped
19. Normal system relief valve pressure is approximately 8300 kPa (1200 psi) with engine operating at 2000 rpm. Refer to paragraph 7 for testing and adjusting procedures.
STEERING CYLINDER
All Models So Equipped
…

Pages from 1856995M1 – AGCO-Massey-Ferguson MF 185MB Baler & Accumulator Workshop Service Manual

Complete workshop & service manual with electrical wiring diagrams for AGCO/Massey-Ferguson MF 185MB Baler & Accumulator. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This AGCO/Massey-Ferguson MF 185MB Baler & Accumulator service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

1856995M1 – AGCO/Massey-Ferguson MF 185MB Baler & Accumulator Workshop Service Manual.pdf

EXCERPT:
Main Roller Bearing Replacement
The main rollers can be removed from the plunger through the side of the baler. Remove only one roller at a time, except when removing the plunger.
Removal
See the safety warnings at the beginning ofthis section and follow the procedures.
1 . Apply the flywheel brake.
2. Disconnect the implement drive line from the tractor.
3. Loosen the cap screws fo~ the shaft retainer.
If you are removinglhe rear roller assembly, loosen the bolt in the pusher plate. Move the shaft retainer out of the groove in the roller shaft and tighten the cap screws.
If you are removing the front roller assembly, loosen the jam nut on the pusher bolt and then loosen the bolt.
Move the shaft retainer out of the groove in the roller shaft and tighten the cap screws.
…

Pages from D3151800 M1 – AGCO-Fendt 8370 P, 8400 P Combine Range + Auto Level + Rotary Separator Workshop Service Manual

Complete workshop & service manual with electrical wiring diagrams for AGCO/Fendt 8370 P, 8400 P Combine Range + Auto Level + Rotary Separator. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This AGCO/Fendt 8370 P, 8400 P Combine Range + Auto Level + Rotary Separator service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

FILELIST:
D3151100 M1 – AGCO/Fendt 8370 P, 8400 P + Auto Level + Rotary Separator Operator’s Manual.pdf
D3151800 M1 – AGCO/Fendt 8370 P, 8400 P Combine Range + Auto Level + Rotary Separator Workshop Service Manual.pdf

EXCERPT:
Table of Contents
0 Introduction – Specifications
1 Cutting table
2 Reel
3 Main crop elevator
4 Threshing unit
5 Straw walkers
6 Shaker shoe- Fanning mill
7 Elevators
8 Engine
9 Unloading auger – Grain tank
10 Drive unit
11 Transmissions
12 Undercarriage
13 Cab
14 Hydraulics
15 Machine housing
16 Electrical system (draft)
17 Straw chopper
18 General assembly instructions
19 Miscellaneous data
…
13.Cab
13.2 Replacing the windscreen
IMPORTANT: The windscreen is glued into the cab and it is advisable to have an expert workshop carry out the replacement. The new windscreen comes with a fitting kit containing the necessary materials, detailed fitting instructions and safety precautions.
1. Dismount the outer roof as described in section 13.4 on page 326.
2. Remove the screws and take off the lamp body on both sides.
3. Remove the screws, including the ones on the back (A), and take the front guard off.
4. Remove the wiper arms.
5. Replace the windscreen in accordance with the fitting instructions provided.
…