Day: May 4, 2019

INSTANT DOWNLOAD (add to cart)

Complete workshop & service manual with electrical wiring diagrams for New Holland T6.120, T6.140, T6.140 AutoCommand, T6.150, T6.150 AutoCommand, T6.155, T6.160, T6.160 AutoCommand, T6.165, T6.175 Tractors. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This New Holland T6.120, T6.140, T6.140 AutoCommand, T6.150, T6.150 AutoCommand, T6.155, T6.160, T6.160 AutoCommand, T6.165, T6.175 Tractor service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

3,823 pages, bookmarked, Searchable, Printable, high quality PDF

New Holland T6.120, T6.140, T6.140 AutoCommand, T6.150, T6.150 AutoCommand, T6.155, T6.160, T6.160 AutoCommand, T6.165, T6.175 Tractor Service Manual
3,823 pages PDF
Part number 47665859 English February 2014
T6.120, T6.140 AutoCommand, T6.140, T6.150 AutoCommand, T6.150, T6.155, T6.160 AutoCommand, T6.160, T6.165, T6.175

EXCERPT:
Hydraulic systems – Reservoir, cooler, and filters
1. Remove the filter guard bracket by unscrewing the three retaining bolts.
2. Before changing the main filter cartridge in housing (3) Figure 2 , release the air bleed valve (2) by unscrewing fully. This will allow air into the filter so that most of the oil can drain back to the reservoir. Wait a few moments and then remove the 19 mm plug (5) from the filter casing and allow the oil to drain out into a suitable container.
3. Using as 41 mm socket or ring spanner, remove the filter support plate by turning approximately 45 ° to the left. Remove filter and plate.
4. Ensure support plate is clean before installing the new cartridge. Lightly oil the sealing ring and refit the assembly to the filter housing, making sure that plate locks into place and the lug (4) aligns correctly with the arrow on the filter casing.
NOTE: When replacing the main filter cartridge the bottom cover sealing ring must also be replaced.
5. Unscrew the charge filter (1) and discard in an appropriate container.
6. Clean the inlet channel and the face of the filter mounting.
Smear clean oil around the rubber seal of the new filter and install into the filter housing. Screw up until the faces just meet, then tighten a further 3/4 of a turn.
Do not over-tighten.
Oil filters – Remove Filter Assembly
1. Remove the hydraulic oil filter vent cap.
NOTE: Leave for one minute to allow oil in the filters to drain into the sump.
2. Remove the filter housing guard bolts (1) and remove the guard.
3. Remove the filter housing drain plug and drain the oil.
NOTE: Place a suitable container under the oil filter housing to collect the hydraulic oil.
…

INSTANT DOWNLOAD (add to cart)

Complete workshop & service manual with electrical wiring diagrams for New Holland T5.95, T5.105, T5.115 Tractor . It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This New Holland T5.95, T5.105, T5.115 Tractor service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

2,173 + 1,290 pages, bookmarked, Searchable, Printable, high quality PDF

New Holland T5.95, T5.105, T5.115 Tractor Service Manual
Part number 84568014 English March 2013

New Holland T5 (T5.95, T5.105, T5.115) Tractor Service Manual
1,290 pages English 07/06/2012
T5.95 NA F5DFL413C*A003
T5.95 WE F5DFL413C*A003
T5.95 INT F5DFL413C*A003
T5.105 NA F5DFL413B*A006
T5.105 WE F5DFL413B*A006
T5.105 INT F5DFL413B*A006
T5.115 NA F5DFL413A*A002
T5.115 WE F5DFL413A*A002
T5.115 INT F5DFL413A*A002
…

EXCERPT:
Front axle system – Powered front axle
Four-Wheel Drive (4WD) axle – Remove 4WD
NOTE: The front axle assembly can be removed from the tractor with either the propshaft removed from or installed in the tractor. The description below refers to removal of the front axle with the drive shaft installed on the tractor. For removal of the drive shaft refer to Front-Wheel Drive (FWD) – Disassemble (23.202) .
1. Fold the steps upwards, after operating the retainer (1) . Turn the retainer (2) to remove the battery cover, then detach the negative cable.
2. Unscrew the bolts (1) and remove the front mudguard supports (2).
3. Remove the split pins, lock pins and front ballast (1).
4. Take out the bolts (1) and remove the drive gear shaft guard (2).
5. Remove the circlip (2) and move the sleeve (1) in the direction indicated by the arrow until it is released from the groove on the drive.
6. Attach the front axle to a hoist using two nylon slings.
7. Raise the tractor and position a fixed stand under the engine sump.
8. Unscrew the hoses of the power steering (1) from the fittings of the pipes (2) .
9. Remove the front differential lock fitting (1) and the hose (2) .
10. Unscrew the retaining bolts and remove the front wheels.
11. Take out the front axle rear support retaining bolts (1).
12. Take out the front axle front support retaining bolts (1).
13. Using the hoist and the two nylon slings, one on each side, detach the front axle.
Four-Wheel Drive (4WD) axle – Install 4 WD
1. Position the axle, tighten the front and rear supports to the relative support.
2. Fit the front wheels.
3. Reconnect the differential lock pipe and the power steering pipes.
4. Using the hoist, raise the front part of the tractor.
5. Extract the fixed stand.
6. Remove the nylon slings from the axle.
7. Connect the drive shaft and position the guard.
8. Refit the two front mudguards.
9. Attach a nylon sling to the front ballasting, fit and secure in position with the lock rod.
10. Reconnect the battery negative lead.
11. Tighten to the prescribed torques (see the tightening torques chapter).
…

INSTANT DOWNLOAD (add to cart)

Complete workshop & service manual with electrical wiring diagrams for New Holland RG140.B Grader, RG 170.B VHP Grader, RG 200.B Grader. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This New Holland RG140.B Grader, RG 170.B VHP Grader, RG 200.B Grader service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

814 pages, bookmarked, Searchable, Printable, high quality PDF

FILELIST:
75314407 – RG140.B Grader, RG 170.B VHP Grader, RG 200.B Grader Service Manual.pdf

EXCERPT:
Table of Contents
Description Section No. Form No.
General Tab 1
Section Index – General 6-46520
Standard Torque Specifications 1001 6-46530
Fluids and Lubricants 1002 6-46540
1003 6-46550
Engines Tab 2
Section Index – Engines 6-46560
For Engine Repair, See the Engine Service Manual
Fuel System Tab 3
Section Index – Fuel System 6-46590
For Fuel System Repair, See the Engine Service Manual
Electrical Tab 4
Section Index – Electrical 6-46600
Removal and Installation of Starter and Alternator 4001 6-42320
ElectricalDiagram 4002 6-46620
Batteries 4003 6-42330
Alternator – 45 Ampere 4008 6-42360
Steering Tab 5
Steering Priority Valve 5004 6-46700
Section Index – Steering 6-46660
Front wheel,axle & wheel lean 5002 6-46780
Steering Control Valve 5003 6-46690
Power Train Tab 6
Section Index – Power Train 6-46730
Transmission Specifications, Pressure Checks, and Troubleshooting RG140.B-RG170.B VHP 6002 6-46750
Transmission Specifications, Pressure Checks, and Troubleshooting RG200.B 6002 6-46750
Transmission -RG 140.B – RG 170.B VHP 6003 6-46760
Transmission-RG 200.B 6003 6-46760
Hydraulics Tab 8
Section Index – Hydraulics 6-46810
Removal and installation of hydraulic components 8001 6-46870
Mounted Equipment Tab 9
Section Index – Mounted Equipment 6-46930
Air Conditioning Troubleshooting
Refrigerant 9002 6-46950
Air Conditioner System Operating instructions 9003 6-46960
Removal and Installation of Air Conditioning Components For Systems with
HFC-134a Refrigerant 9004 6-46970
Front Blade 9009
RG 140.B – RG 170.B VHP – RG200.B GRADERS
Service Manual
75314407
Brake pedal valve and system 7003 6-46840
Tandem drive limited slip rear axle-RG 140.B – RG 170.B VHP 6006 6-46790
Tandem drive differential hydraulic lock-RG 170.B VHP – RG 200.B 6006 6-46790
Limited slip rear axle-RG 140.B – RG 170.B VHP 6005 6-46760
Rear axle with differential lock-RG 140.B – RG170.B VHP – RG 200.B 6005 6-46780
Section Index- Brakes 6-46810
Hydraulic brakes troubleshooting 7002 6-46830
Frame, articulation joint, circle and scarifier 9008 6-47000
Rear Ripper 9007 6-47010
ROPS Cab 9010 6-47030
Brakes Tab 7
Cab Glass Installation 9011 6-47040
…
ASSEMBLE INPUT SHAFT
1. Align marks made on input shaft (A) and gear (B).
2. Install gear on input shaft.
3. Install thrust race (C). NCAUTION: Wear safety glasses when removing or installing snap rings.
4. Install snap ring (D).
IMPORTANT: Always use new seal rings. The seal rings must be sized to fit the shaft groove tightly to prevent damage during installation. Check that seal ring is in place and sized immediately before assembly.
5. Size the seal ring (E) by twisting in a tight circle, approximately 25 mm (1 in) in diameter.
6. Apply grease to the seal ring and seal surfaces.
7. Install seal ring (E).
…

INSTANT DOWNLOAD (add to cart)

Complete workshop & service manual with electrical wiring diagrams for New Holland Wheeled Excavators MH2.6, MH3.6, MH City, MH Plus, MH 5.6, MH6.6, MH6.6 Industry, MH8.6, MH8.6 Industry. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

New Holland Wheeled Excavators MH2.6, MH3.6, MH City, MH Plus, MH 5.6, MH6.6 (Industry), MH8.6 (Industry) service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

5,306 pages, bookmarked, Searchable, Printable, high quality PDF

FILELIST:
Training Material (Wheeled Excavators MH CITY to MH 8.6 Tier3)
604.07.246.50 – MH 2.6 – MH 3.6 Flat Time Rate Manual & Fault Code.pdf
604.13.477 – MH2.6 – MH3.6 Wheel Excavators Repair Manual.pdf
604.13.557 – MH City, MH Plus, MH 5.6 Hydraulic Excavator Workshop Manual.pdf
604.13.562 – MH6.6, MH8.6 Hydraulic Excavator Workshop Manual.pdf
87677413A – MH City – MH Plus – MH 5.6 Wheel Excavators (Tier 3) Repair Manual.pdf
87677418A – MH 6.6 – MH 6.6 Industry – MH 8.6 – MH 8.6 Industry Wheel Excavators Repair Manual.pdf
87730662A – MH2.6 – MH3.6 Wheel Excavators (Tier 3) Repair Manual.pdf

EXCERPT:
SECTION 01 MAIN
OPERATING RULES
1. INTRODUCTION … 1
1.1 FOREWORD ….. 1
1.2 MANUAL HANDLING…. 1
SECTION 02 SAFETY
PRECAUTIONS
1. SAFETY PRECAUTIONS…… 1
2. SAFETY DECALS … 41
SECTION 03 FEATURES
AND DATA
1. FOREWORD ….. 1
2. IDENTIFICATION DATA…. 2
3. NOISE LEVELS (2000/14/EC)…. 3
4. SUMMARY PLATE FOR MAINTENANCE OPERATIONS….. 5
5. WHEELED EXCAVATOR MAIN COMPONENTS…… 6
5.1 TECHNICAL SPECIFICATIONS …. 7
5.2 OPERATING WEIGHTS… 17
5.3 DIGGING PERFORMANCE….. 18
5.4 TRANSPORT DIMENSIONS…. 20
5.5 BUCKET USEFULNESS DEPENDING ON ARM …. 24
6. FILLING CHART…… 26
SECTION 04 UPPER
STRUCTURE
1. UPPER STRUCTURE … 1
2. MAIN FRAME AND COUNTERWEIGHT…. 5
3. POWER UNIT…. 9
3.1 ENGINE… 10
4. RADIATOR…… 12
5. HYDRAULIC PUMPS … 14
5.1 MAIN PUMP …. 15
5.2 DOUBLE PUMP WITH GEARS…. 49
6. AIR CLEANER….. 61
7. EXHAUST SILENCER….. 62
8. HYDRAULIC OIL TANK… 64
9. FUEL TANK….. 66
10. FUEL TRANSFER PUMP….. 67
11. GUARDS AND COVERS….. 70
12. CAB ….. 76
13. SWINGING ASSY…. 88
14. MAIN CONTROL VALVE…. 100
15. SLEW DEVICE …… 124
15.1 SLEW HYDRAULIC MOTOR ….. 126
15.2 SLEW REDUCTION UNIT…… 140
16. CONTROL LEVER …. 159
17. CONTROL PEDAL …. 164
18. STEERING UNIT … 166
19. SWIVEL JOINT …… 191
19.1 FEATURES AND DATA…… 193
20. BRAKE PEDAL VALVE …… 194
21. ACCUMULATORS….. 208
22. PRESSURE SWITCHES …. 211
23. SOLENOID VALVES …… 215
SECTION 05 UNDERCARRIAGE
1. SLEWING BEARING ….. 2
2. LOWER FRAME …. 5
3. TRAVEL ASSY …… 6
3.1 TRAVEL HYDRAULIC MOTOR…… 7
3.2 SPEEDS GEAR BOX…. 23
3.3 STEERING AXLES: FRONT AND REAR….. 52
3.4 RIGID REAR AXLE….. 150
3.5 DRIVE SHAFT … 213
4. WHEELS AND TYRES … 214
4.1 TYRES… 222
5. BLADE … 227
6. LATERAL STABILIZERS… 228
SECTION 06 FRONT
ATTACHMENT
1. INTRODUCTION … 1
2. CYLINDER REMOVAL AND INSTALLATION…. 6
2.1 BUCKET CYLINDER….. 6
2.2 ARM CYLINDER…… 10
2.3 POSITIONING CYLINDER … 14
2.4 BOOM CYLINDER… 19
3. MH2.6 – CYLINDERS… 24
3.1 BUCKET CYLINDER… 24
3.2 ARM CYLINDER…… 31
3.3 POSITIONING CYLINDER … 38
3.4 BOOM CYLINDER… 45
4. MH3.6 – CYLINDERS… 52
4.1 BUCKET CYLINDER… 52
4.2 ARM CYLINDER…… 59
4.3 POSITIONING CYLINDER … 66
4.4 BOOM CYLINDER… 73
5. ANTIDROP VALVE…… 81
6. PINS AND BUSHINGS ….. 83
7. BUCKETS…. 88
SECTION 07 HYDRAULIC
SYSTEM
1. HOSES AND FITTINGS ….. 1
2. HYDRAULIC SYSTEM … 8
2.1 MAIN PIPELINES … 8
2.2 SUCTION AND DELIVERY PIPELINES….. 9
2.3 RETURN PIPELINES…… 11
2.4 DRAINING PIPELINES….. 13
2.5 FRONT ATTACHMENT PIPELINES…. 17
2.6 NIBBLER/BREAKER CONTROL PIPELINES…… 18
2.7 SLEW CONTROL PIPELINES – TRAVEL AND BLADE/STABILIZERS… 23
2.8 STEERING PIPELINES (MACHINE 4WD)… 25
2.9 STEERING PIPELINES (MACHINE 2WD)… 28
2.10 BRAKE PIPELINES….. 31
2.11 POWER STEERING PIPELINES….. 35
2.12 LATERAL STABILIZERS AND BLADE CONTROL PIPELINE….. 40
2.13 LOCK VALVES…. 44
2.14 STABILIZERS/BLADE SELECTION VALVE…. 45
2.15 FRONT AXLE LOCK …. 46
2.16 AXLE LOCK VALVE….. 48
2.17 PRESSURE RELIEF VALVE…. 48
3. OPERATION OF CIRCUITS….. 50
SECTION 08 ELECTRICAL
SYSTEM
1. SAFETY PRECAUTIONS…… 1
2. FEATURES AND DATA ….. 2
3. COMPONENTS LOCATION AND OPERATION…. 3
4. UNDERCARRIAGE ELECTRIC COMPONENTS… 6
4.1 MACHINE WITH FOUR STEERING WHEELS …… 6
4.2 MACHINE WITH TWO STEERING WHEELS…. 7
5. CONTROL UNITS ELECTRIC SYSTEM…. 7
6. LIGHT AND BEAMS GROUP….. 8
7. GAUGES AND CONTROLS… 9
7.1 DASHBOARDS…… 9
7.2 CONTROL LEVERS….. 11
7.3 SWITCHES AND CONTROL LIGHTS PANEL….. 12
7.4 SWITCHES AND WARNING LAMPS… 13
7.5 MONITOR PANEL… 14
7.6 KEY START SWITCH… 26
7.7 LEFT CONTROL LEVER…… 27
7.8 RIGHT-HAND CONTROL LEVER…. 28
7.9 CONTROL PANEL AND SWITCHES… 29
7.10 MACHINE CONTROL CARD … 32
7.11 PUMP CONTROL CARD…… 34
8. ELECTRIC COMPONENTS ….. 36
8.1 THROTTLE LEVER CONTROL … 36
8.2 SWIVEL JOINT…. 37
8.3 BATTERIES….. 38
8.4 GENERATOR…… 39
8.5 STARTER…. 40
9. CONTROL LINE AND WIRING HARNESSES….. 41
9.1 CONTROLS ON CONSOLES …… 41
9.2 CONTROLS FOR SIDE PANEL SWITCHES… 49
9.3 ANTI-TILTING CHECK CONTROL LINE ….. 51
9.4 WORKING LIGHTS CONTROL LINE… 52
9.5 TRAFFIC BEAMS CONTROL LINE…… 53
9.6 STEERING COLUMN CONTROLS…… 58
SECTION 09 TROUBLESHOOTING
1. INTRODUCTION … 1
2. HYDRAULIC SYSTEM TROUBLESHOOTING …… 3
3. ELECTRICAL SYSTEM TROUBLESHOOTING… 28
SECTION 10 PERFORMANCE
TEST
1. INTRODUCTION … 1
1.1 GENERAL INFORMATION FOR MACHINE TESTING…… 1
2. STANDARD PERFORMANCES – MH2.6 … 3
2.1 TABLE OF EXCAVATOR STANDARD PERFORMANCES… 3
2.2 HYDRAULIC COMPONENTS STANDARD PERFORMANCE… 5
2.3 MAIN PUMP P-Q CURVE… 6
3. STANDARD PERFORMANCES – MH3.6 … 7
3.1 TABLE OF EXCAVATOR STANDARD PERFORMANCES… 7
3.2 HYDRAULIC COMPONENTS STANDARD PERFORMANCE… 9
3.3 MAIN PUMP P-Q CURVE….. 10
4. PREPARATION FOR PERFORMANCE TEST….. 11
5. EXCAVATOR PERFORMANCE TEST….. 13
5.1 ENGINE PERFORMANCE … 13
5.2 SWING PERFORMANCE….. 14
5.3 FRONT ATTACHMENT PERFORMANCE… 18
5.4 CONTROL LEVERS….. 21
6. BOOM/SLEW PERFORMANCE… 22
6.1 COMBINED SLEW/BOOM TEST ….. 22
6.2 STEERING… 23
6.3 BRAKES SYSTEM… 24
7. GEAR BOX …… 27
7.1 GEAR BOX PRESSURE CHECK….. 27
8. COMPONENTS PERFORMANCE … 28
8.1 OVERPRESSURE VALVE AND PILOT CONTROL LINE…. 28
8.2 OVERPRESSURE RELIEF VALVES … 30
8.3 DRIVE SHAFT ….. 33
8.4 HYDRAULIC PUMPS – MH2.6…… 35
8.5 HYDRAULIC PUMPS – MH3.6…… 37
8.6 TRAVEL MOTOR….. 39
…
DISASSEMBLING
The disassembly procedure below starts on the premise that the hydraulic lines and the line securing bands have been removed.
WARNING
Arm cylinder weight: 86 kg (189 lb).
Lift and securely place the cylinder on a workbench using a crane. Be sure that the cylinder is placed horizontally. Drain hydraulic oil from the cylinder.
Fully extend the cylinder rod (1). Secure the rod end using a crane. Remove the screws (7) from the cylinder head (4).
NOTE: be sure to pull out the cylinder rod (1) straight so as not to damage the sliding surfaces.
Pull out the cylinder head (4) from cylinder liner (2) by tapping with a plastic hammer. Remove the cylinder rod (1) and the cylinder head (4).
…

INSTANT DOWNLOAD (add to cart)

Complete workshop & service manual with electrical wiring diagrams for New Holland LS180.B, S185.B, S190.B Skid Steer Loader. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This New Holland LS180.B, S185.B, S190.B Skid Steer Loader service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

837 pages, bookmarked, Searchable, Printable, high quality PDF

New Holland LS180.B, S185.B, S190.B Skid Steer Loader Repair Manual
Print No. 604.13.552.01 English

CONTENTS
INTRODUCTION
DISTRIBUTION SYSTEMS
PRIMARY HYDRAULIC POWER SYSTEM SECONDARY HYDRAULIC POWER SYSTEM HIGH-FLOW HYDRAULIC POWER SYSTEM ELECTRICAL POWER SYSTEM
LIGHTING SYSTEM
POWER PRODUCTION ENGINE
FUEL AND INJECTION SYSTEM AIR INTAKE SYSTEM
ENGINE COOLANT SYSTEM LUBRICATION SYSTEM STARTING SYSTEM
POWER TRAIN
POWER COUPLING Fixed coupling
TRANSMISSION Hydrostatic
TRAVELLING
FRONT AXLE
REAR AXLE
STEERING Steering clutch
PARKING BRAKE Hydraulic
WHEELS AND TRACKS Wheels Final drive
BODY AND STRUCTURE
USER CONTROLS AND SEAT
USER PLATFORM
ENVIRONMENT CONTROL Heating system
ENVIRONMENT CONTROL Air-conditioning system SAFETY SECURITY ACCESSORIES Safety
WORKING ARM
BOOM Lift
SINGLE ARM Lift
SINGLE ARM TOOL ATTACHMENT Tilt
TOOLS AND COUPLERS CARRYING Unarticulated tools COUPLING Hydraulic coupling
COUPLING Mechanical coupling
…

EXCERPT:
Alternator – Replace (A.30.A.82 – F.10.A.30)
1. Use a suitable support between the front bearing and the bearing retainer on the rotor shaft. Press the rotor shaft out of the front bearing and the spacer.
2. Remove the bearing retainer.
3. Use a suitable support between the rear bearing and the slip ring on the other end of the rotor shaft. Press the rotor shaft out of the rear bearing.
4. Install the bearing retainer on the rotor shaft.
5. Press the new front bearing onto the rotor shaft until the front bearing stops moving.
6. Press the spacer onto the rotor shaft until the spacer stops moving.
7. Press the new rear bearing onto the other end of the rotor shaft.
…