Complete workshop & service manual with electrical wiring diagrams for AGCO/Massey-Ferguson Tractor Series 8400 (models 8450, 8460, 8470, 8480). It’s the same service manual used by dealers that guaranteed to be fully functional.
This AGCO/Massey-Ferguson Tractor Series 8400 (models 8450/8460/8470/8480) service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.
FILELIST:
3378886M1 – AGCO/Massey-Ferguson Tractor Series 8400 (models 8450/8460/8470/8480 Dyna VT) Operator Instruction Book.pdf
AGCO/Massey-Ferguson Tractor Series 8400 (models 8450/8460/8470/8480) Workshop Service Manual (Section 3&5-12).pdf
TABLE OF CONTENTS
03 – Engine
03A01 – Sisu engine – General
03B10 – SISU TIER 3 ENGINE – General
03B11 – SISU TIER 3 ENGINE – Removing and refitting
05 – Gearbox
05A01 – General – Dyna VT Operation
05B01 – DYNA VT hydraulics
05C01 – Replacing the DYNA VT unit
06 – Rear axle
06B01 – Final drive units
06C01 – Braking unit
07 – Power take off
07A01 – Rear PTO
07B01 – Assembling and disassembling the rear PTO
08 – Front axle
08B01 – DANA final drive units
08D01 – DANA bearings and transmission shafts
08E01 – 4-wheel drive clutch
08E02 – Universal joint shaft brake
09 – Hydraulics
09A01 – Description of the circuit
09B01 – Illustrated diagram
09C01 – Hydraulic legends and diagrams
09D01 – Layout of components
09E01 – Trailer braking and ParkLock
09F01 – Auxiliary spool valves
09G01 – Lift control valve
09H01 – Load Sensing hydrostatic steering
09I01 – Main braking circuit
09J01 – Disassembling and reassembling the pumps
09K01 – Auxiliary hydraulics tests
10 – Electrical equipment
10A01 – Fuse box
10A02 – Electrical diagrams
11 – Electronics
11B10 – EEM2 SisuDiesel – Description
GUF101 – SisuDiesel ELECTRONIC INJECTION – Programming
GUF102 – SisuDiesel ELECTRONIC INJECTION – Tests and diagnostics
GUF103 – SisuDiesel ELECTRONIC INJECTION – Error codes
GUF105 – SisuDiesel ELECTRONIC INJECTION – Electrical Diagrams
11C10 – DCC2 – Description
GUF211 – DCC2 (DynaVT) – Programming and setting parameters
GUF213 – DCC2 (DynaVT) – Error codes
GUF214 – DCC2 (DynaVT) – Calibrations, constants and adjustments
GUF215 – DCC2 (DynaVT) – Electrical diagrams
11D10 – Autotronic 4 – Description
GUF401 – AUTOTRONIC 4 – Programming and setting parameters
GUF402 – AUTOTRONIC 4 – Tests and diagnostics
GUF403 – AUTOTRONIC 4 – Error codes
GUF404 – AUTOTRONIC 4 – Calibration
GUF405 – AUTOTRONIC 4 – Electrical diagrams
11E10 – Autotronic 5 ParkLock – Description
GUF531 – AUTOTRONIC 5 – ParkLock DynaVT – Programming and setting parameters
GUF532 – AUTOTRONIC 5 – DynaVT ParkLock – Tests and diagnostics
GUF533 – AUTOTRONIC 5 – DynaVT ParkLock – Error codes
GUF535 – AUTOTRONIC 5 – ParkLock DynaVT – Electrical diagrams
11F10 – Autotronic 5 – Linkage – Description
GUF521 – AUTOTRONIC 5 – Linkage – Programming and setting parameters
GUF522 – AUTOTRONIC 5 – Linkage – Tests and diagnostics – MF6400/7400/8400
GUF523 – AUTOTRONIC 5 – Linkage – Error codes – MF6400/7400/8400
GUF524 – AUTOTRONIC 5 – Linkage – Calibration and adjustments
GUF525 – AUTOTRONIC 5 – Linkage – Electrical diagrams – MF6400/7400/8400
11G10 – Datatronic 3 – Description
GUF601 – DATATRONIC 3 – Programming
GUF604 – DATATRONIC 3 – Calibration and adjustments
GUF605 – DATATRONIC 3 – Electrical diagrams
GUF71 – SMS – JOYSTICK / FingerTIP – Setting parameters
GUF72 – SMS – JOYSTICK – Tests and diagnostics
GUF73 – SMS – JOYSTICK / FingerTIP – Error codes
GUF74 – SMS – JOYSTICK – Settings
GUF75 – SMS – JOYSTICK / FingerTIP – Electrical diagrams – Auto 5 linkage
11I10 – Autotronic 5 – Suspended front axle – Description
12 – Cab and equipment
12C01 – Air conditioning – General
12C02 – Standard air conditioning
12C03 – Automatic air conditioning
GUF302- AUTOMATIC AIR CONDITIONING – Tests and diagnostics
GUF303- AUTOMATIC AIR CONDITIONING – Error codes
GUF305- AUTOMATIC AIR CONDITIONING – Electrical diagrams
12C04 – Air conditioning – Refilling the unit
EXCERPT:
K . Disassembling the lower bush
Disassembling the bush (23 Fig. 13)
101.Using the lever located to the right under the steering wheel, pull the steering column as far as possible towards the driver.
102.Take off the steering wheel and the instrument panel lower cover (1). Disconnect the connectors of the reverse shuttle, wiper control unit and DOT
MATRIX keyboard (if fitted).
103.If there is not sufficient access space, also take out the upper cover (2) and instrument panel (3) (Fig. 14).
104.Remove the 4 attachment screws fixing the column base to the cab support.
105.Take off the column assembly.
106.Remove the half housings around the steering column. Take off the reverse shuttle control, lighting switch and DOT MATRIX keyboard (if fitted).
107.Remove and discard the retaining washers (1)(2).
Remove the spring (3) and lever (4) with the boot (8) and lever (6).
108.Press on the notched levers (9)(10) to compress the spring (7). Take off the nuts (14). Take off the steering racks (11) and (12).
109.Drive out the pin (15). Remove the notched levers (9)(10) and the spring (7).
110.Take out the adjusting screw (5) (3mm Allen key).
111.Disassemble the nuts (16) and their respective screws, and separate the upper articulated part (17) of the column.
112.Disassemble the nuts (18) and their respective screws, and separate the lower part (19) of the column.
113.Remove the arm (20) and brake plate and nut (21).
114.Extract the bush (23) from the housing (19).
…
