Day: August 6, 2018

Pages from 81.99298-4932 – MAN Hypoid Axles HY-1336-B Repair Manual F19

INSTANT DOWNLOAD (add to cart)

Complete workshop & service manual with electrical wiring diagrams for MAN Trucks & Buses. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This service & repair manual collection (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

FILELIST: (about 2G PDFs)
├── 1290 751 105a – ZF-ECONLiTE 6 S 850, 6 S 890 Shop Manual.pdf
├── 1304 751 103a – ZF-ECONMid 16 S 109 Service Manual.pdf
├── 1307 763 102c – ZF-Ecolite Special Features.pdf
├── 1315 751 101d – ZF-ECONSPLiT 16 S 151, 8 S 151 Shop Manual.pdf
├── 1315 751 102a – ZF-ECONSPLiT NMV 221, i-0.98, i-1.55 Service Manual.pdf
├── 1315 751 110a – ZF-ECONSPLiT Shift system with PSU (Pneumatic Servo Unit) Repair Manual.pdf
├── 1316 751 101c – ZF-ECONSPLiT 16 S 221, 16 S 181, 8 S 181 Service Manual.pdf
├── 1316 751 102 – ZF-ECONSPLiT 16 S 251 Service Manual.pdf
├── 1327 751 101 – ZF-AS TRONic 10 AS 2301, 12 AS 2301, 16 AS 2601 (Repair stages 1-2) Repair Manual.pdf
├── 1327 751 102 – ZF-AS TRONic 10 AS 2301, 12 AS 2301, 16 AS 2601 (Repair level 3) Repair Manual.pdf
├── 25 1818 95 14 86 – Hydronic 16_24_30_35 Heater Troubleshooting and Repair Manual.pdf
├── 4130 751 103a – ZF-TRANSMATiC WSK 400 for 16 S 151, 16 S 221, WSK 440 for 16 S 251 Service Manual.pdf
├── 51.99493-8414 – MAN D2840 LE_LXE 401_402_407, D2842 LE_LYE_LZE 401_402_403_406_408_411_412_413, D2848 LE_LXE 401_403_405 Marine Diesel Engine Repair Manual.pdf
├── 51.99493-8428 – MAN Marine Diesel Engines D2866LE 401-402-403-405 & D2876LE 301-403.pdf
├── 51.99493-8504 – MAN D2840 LE2…, D2842 LE2…, D2848 LE2… Industrial Diesel Engine Repair Manual.pdf
├── 51.99598-8021 – MAN M(S) 5 – D 28 V-Marine Engines Electrical Diesel Control EDC Repair Manual.pdf
├── 51.99598-8038 – MAN D2848 LE 602_604_606_607 Industrial Diesel Engine Repair Manual.pdf
├── 51.99598-8049 – MAN Electrical Diesel Control EDC M(S) 5 – D 2842 LE6.. Repair Manual.pdf
├── 81.99198-5912 – MAN Hypoid Axles HY-1175, HDY-1175 Repair Manual F18.pdf
├── 81.99198-5972 – MAN Trucknology Generation A (TG-A) Electrical System Wiring Diagrams.pdf
├── 81.99198-6762 – MAN Driven Front Axle VP-09 Repair Manual G5.pdf
├── 81.99198-6892 – MAN Driven Front Axle VPD-09 Repair Manual G6.pdf
├── 81.99198-6922 – MAN Planetary Axle HP-1333 F38 Repair Manual.pdf
├── 81.99198-6952 – MAN Non-driven Front Axles VOK-05-01~06 Repair Manual H10.pdf
├── 81.99198-7132 – MAN Live Hypoid Rear Axle HY-0925 F22.pdf
├── 81.99198-7852 – MAN Live Hypoid Rear Axle HY-0512 Repair Manual F20.pdf
├── 81.99198-7882 – MAN Live Hypoid Rear Axle HY-0718 Repair Manual F21.pdf
├── 81.99198-7912 – MAN Non-driven Front Axles VOK-03-01, VOK-03-02 Repair Manual H11.pdf
├── 81.99198.4222 – MAN Forward-control Trucks Heavy Range F2000 & Medium Range M2000-M Electrical System Repair Manual T32.pdf
├── 81.99298-4932 – MAN Hypoid Axles HY-1336-B Repair Manual F19.pdf
├── 81.99298-6842 – MAN Electrical System Common-Rail Injection System EDC7 System Description T18.pdf
├── 81.99298.4002 – MAN FRH Coach, Lion’s Star Electrical System Repair Manual T20.pdf
├── 81.99298.4322 – MAN Driven Rear Axles (AP Axles for Buses) Repair Manual F 4-B.pdf
├── 81.99298.4322 – MAN Driven Rear Axles (AP Axles for Buses) Repair Manual F4-B.pdf
├── 81.99589-5062 – MAN Maintenance Recommendations & Recommended Service Products – Commercial Vehicles, OEM Components & Rail Vehicles.pdf
├── 81.99593-4092 – MAN In-line Engines D 28.. – 4-valve Cylinder Head Repair Manual 2nd Supplement A11.pdf
├── 81.99593-4242 – MAN In-line Engines D 02- & D 08- Series Repair Manual 2nd Supplement A 13 (3.).pdf
├── 81.99598-4022 – MAN Electrical System Electronic Diesel Control (EDC) MS5, M(S) 5 System Description T17-A.pdf
├── 81.99598-43 – MAN In-line Engines D 02- & D 08- Series Repair Manual A13.pdf
├── 81.99598-4462 – MAN D 25.. – D 28.. – 2-valve & 4-valve cylinder head In-line Engines Repair Manual incl. 1st supplement A11.pdf
├── 81.99598-4572 – MAN Non-Driven, Steering Front-, Leading, Trailing Axles (V7-_V9-.. L,SL_HN7-_.. SL) Repair Manual H6.pdf
├── 81.99598-4632 – MAN Hypoid Axles HY 0855, 0955, 1175, 13110, HOY 0955, 1175 Repair Manual F10.pdf
├── 81.99598-4752 – MAN Driven Rear Hypoid Axle HY-1350 Repair Manual F13.pdf
├── 81.99598-4842 – MAN Driven Hypoid Rear Axle HY-0720 Repair Manual F16.pdf
├── 81.99598-5442 – MAN Front Leading & Trailing Axles Repair Manual H8.pdf
├── 81.99598-6132 – MAN Disc Brake SN 5000 Repair Manual P109.pdf
├── 81.99598.4662 – MAN Electronically Controlled Diesel Injection EDC MS 6.4 Repair Manual T17-A2.pdf
├── 81.99598.58 – MAN Common Rail System EDC System Description T18 2nd Edition.pdf
├── 81.99598.5892 – MAN Common Rail System EDC 7 System Description T18.pdf
├── 83.99297-XXXX – MAN EMI-Low-Floor Regular-service Buses EL 223_283, NL-HD 223_283 Maintenance Manual WA 78 (2nd).pdf
├── EDC MS5 – MAN Training Documentation EDC MS5 Step 3 EURO II, Step 5 EURO III.pdf
├── EDC_MS64 – Training document EDC MS 6.4.pdf
├── Fundamentals of Commercial Vehicle Technology – Basic Infomation on Trucks & Buses
│…
├── MAN D-0834_36 Engine EURO2-3 Training Course.pdf
├── MAN D2066 LF.. with EDC 7 Common Rail Engine Training Course.pdf
├── MAN Engine D 2866_76 Euro 2-3 Training Documentation.pdf
├── MAN Engine Training D 2876 LF 12_13 Common Rail AT-01c.pdf
├── MAN L2000 M2000 F2000 Construction Period 1992-2005 (according to model) Service Manual.pdf
├── MAN Lehrgangsunterlage ZF Getriebe 16 S 151_181_221_251 Ecosplit (DE).pdf
├── MAN Service Akademie EDC 7 Common Rail Training.pdf
├── MAN Trucknology Generation A (TGA) Shop Manual.pdf
├── MAN Trucknology Generation S and X (TGS_TGX) Shop Manual.pdf
├── Trucknology Generation L and M (TGL_TGM) Shop Manual.pdf
└── bonus_material
├── 81.99198-476 – MAN Trucknolgy Generation A (TG-A) Instalatia Electrica Scheme de Conexiuni K90 (RO).pdf
├── 81.99198-4876 – MAN Trucknology Generation A (TG-A) Sistemul electronic de franare (EBS) Instalatia Electrica Descrierea sistemului T61 (RO).pdf
├── 81.99198-490 – MAN Trucknology Generation A (TG-A) Instrumentatie Instalatia Electrica Descrierea sistemului T62 (RO).pdf
├── 81.99198-5026 – MAN Trucknology Generation A (TG-A) Intarder EST 48 Instalatia Electrica Descrierea sistemului T67 (RO).pdf
├── 81.99198-5086 – MAN Trucknology Generation A (TG-A) Instalatia de climatizare Instalatia Electrica Descrierea sistemului T69 (RO).pdf
├── 81.99198-53 – MAN Trucknology Generation A (TG-A) Modulul Portierei Instalatia Electrica Descrierea sistemului T77 (RO).pdf
├── 81.99198-5356 – MAN Trucknology Generation A (TG-A) Airbag Instalatia Electrica Descrierea sistemului T78 (RO).pdf
├── 81.99198-541 – MAN Trucknology Generation A (TG-A) Instalatia electrica centrala Descrierea sistemului T80 (RO).pdf
├── 81.99198-544 – MAN Trucknology Generation A (CAN_ZBR_FFR) – CAN-Controller Area Network (Descrierea sistemului T51-A1) – Instalatia Electrica (RO).pdf
├── 81.99598-470 – MAN Trucknology Generation A (TG-A) Instalatia electrica Injeclia de motorina cu reglaj electronic (EDC) MS 6.1 Descrierea sistemului T17-A3 (RO).pdf
├── 81.99598-497 – MAN Instalatia electrica – Legenda, numere de cod numere de cabluri, simboluri… Lista aparatelor T60 (RO).pdf
├── 81.99598-54 – MAN Modulul de comanda amplasat in USA Instalatia Electrica Descrierea sistemului T77 (RO).pdf
├── Coupling devices TG Service Manual.pdf
├── MAN Error Codes.pdf
├── MAN Interfaces TG Service Manual.pdf
├── MAN-Schite electrice
│   …
├── Power Take-Offs At Eaton-Gearbox.pdf
├── Power Take-Offs Service Manual.pdf
├── Power Take-Offs at ZF-Gearbox.pdf
├── Pump Installation Service Information_1st supplement to 37500 en.pdf
├── ZDR (Intermediate Engine Speed Control) Interface with Customer Specific Control Module (KSM) for External Engine Speed Control & Fleet Management(FMS) Interface On TGA.pdf
├── ZDR Interface with Customer-Specific Control Module (Step 1) for External Engine Speed Control & Fleet Management Interface on TG.pdf
├── ZDR Interface with Vehicle Management Computers for External Speed Controls with the Trucknology Generation.pdf

EXCERPT:
Functional description
The hypoid rear axle for buses is described in this repair manual.
The axle is designed for an exceptionally long, maintenance-free service life. The axle is a live, non-steering rigid axle with a single reduction ratio. There is a choice of reduction ratios available for the axle drives. This axle is installed as a single axle.
The power flows from the gearbox to the rear axle input flange via the propshaft.
The power flows from the input flange to the rear axle via the countershaft gears, drive pinion/crown wheel, differential and axle shafts. From here, the power is transmitted to the wheel hub and the driven wheels.
The axle drive consists of the drive pinion/crown wheel assembly and the differential. The differential function is provided by a differential spider. The input flange has cross serrations.
The axle housing is made from fine-grained steel and is oil-tight. The two steel axle journals are welded to the axle housing. The flange for locating the sliding calliper carrier is welded onto the axle housing.
The brake is a compressed air-operated sliding-calliper disc brake with automatic adjustment and a continuous wear indicator. It is a single unit comprising service brake, auxiliary brake and parking brake. It is operated mechanically by means of a combination brake cylinder directly on the sliding calliper. The automatic adjustment feature takes effect depending on the degree of wear and operates with a fixed clearance.
The internally ventilated brake discs are bolted onto the wheel hubs.
The ABS consists of a ring with built-in speed sensor, which is shrunk onto the axle housing (axle tube). The ABS pulse generator for the ABS speed sensor is part of the hub-unit wheel bearing unit and is pressed into the wheel hub.
The hub-unit wheel bearing unit is a “constructed” encapsulated wheel hub bearing unit and constitutes a single component.
The wheel hub, bearing, rotary shaft seals and ABS pulse wheel (rotor) are assembled into an encapsulated unit.
These wheel bearings are not adjustable and have a lifetime grease filling for lubrication. No measurable clearance is permitted on the hub-unit wheel bearings.
The brake pads are asbestos free. A checking device informs the driver when the wear limit is reached.
The parking brake is applied via the brake cylinder spring actuators.
…

Atlet 2008-2011

Complete digital official shop manual contains service, maintenance, and troubleshooting information for the Atlet Forklift Trucks 2008-2011. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual for Atlet Forklift Trucks 2008-2011 is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

MAKE: Atlet
MODEL: T / A / X / U / O / P Chassis
FORMAT: PDF
SIZE: 435 MB
LANGUAGE: English / German / French / Swedish

MAKE: Atlet
MODEL: T / A / X / U / O / P Chassis
FORMAT: PDF
SIZE: 484 MB
LANGUAGE: English / German / French / Swedish

Atlet Forklift Trucks Spare Parts Catalog, Service Manual, and Electrical Diagrams

├── T Chassis
│   ├── TLL / TLP
│   ├── TP
│   ├── TS
├── A Chassis
│   ├── A
│   ├── A-Ergo
├── X Chassis
│   ├── X-90
│   ├── X-Ergo
├── U Chassis
│   ├── UNN
│   ├── URF AC (Powder Plus)
│   ├── U*S AC (Powder Plus)
│   ├── U-TERGO
├── O Chassis
├── P Chassis
│   ├── PLL
│   ├── PLP
│   ├── PP
│   ├── PS

BONUS.MATERIAL:
Warehouse 2008B (PDF, 49 MB)
A-Ergo
OP
PLL-PSD-PSL-PLE
PLP
PP
PS
T
U
X-Ergo

Atlet (Eden Farm) (PDF, 12 MB)
Electrical Diagrams
U Tergo
UNS_UHS

EXCERPT:
7.2.2.4 Operation test of steering servo system – fly by wire
1. Log on the truck and check that the operation of the end stops in both directions is correct.
2. Turn the mini wheel clockwise to the maximum. Connect the red/black cable with the pink/black cable coming from X18’s connection closest to the servo box. Turn the steering to the centre position. After approx. 10 mm of movement on the gearbox the servo contactor should open. Check that the brakes are properly applied and that it is not possible to drive the machine. If
the brakes are not on and the machine can be driven then the circuit must be checked. The drive controller E1 is supplied from the servo contact E4 pin 8.
Check that pin 8 is not live, if it is – replace the servo box. Reset using the off-on buttons on the keyboard.
3. Brown/white cable. Perform the equivalent procedure with the switch by connecting together the red/black cable with the brown/white cable.
4. Pull apart the connector P14 (tied to the return hose on UNS). The servo contactor should open and it should be impossible to release the brake; it should also be impossible to drive the truck. Connect P14 again.
5. Pull out the motor fuse for the servo motor (F4). The servo motor should
open and it should be impossible to release the brake; it should also be impossible to drive the truck. Fit the fuse again.
6. If it is possible to release the brake after points 2, 3, 4 or 5 have been implemented, or it is possible to drive the truck, the truck must be checked carefully and not used until the fault has been rectified.
7. Finally check that the drive unit does not hit the mechanical stop in the end
positions.

7.2.2.5 Mechanical adjustment to the steering sensors – EPS 2001/ EPS AC0
With the gear box on the seat side of the truck, turn the drive wheel anticlockwise a little over +90 degrees (Circa +100 degrees) ensuring that the cam on the drive unit is located under both threaded holes for the sensors.
Screw in the sensor (follow with the cable to avoid twisting) until it reaches the bottom on the cam. Then unscrew the sensor a 3/4 turn and lock the sensor with the nut.
Important!
The nut is to be locked using thread locking solution. However, make sure that the thread locking solution is not applied in the threaded hole.

7.2.2.6 Operation test of the steering sensors – EPS 2001/EPS AC0
1. With the gear box on the seat side of the truck, turn the drive wheel anticlockwise a little over +90 degrees (Circa +100 degrees) ensuring that the cam on the drive unit is located under both threaded holes for the sensors.
2. Switch off the truck.
3. Disconnect the cable to the steering sensor.
4. Unscrew the steering sensor (follow with the cable to avoid twisting).
5. Reconnect the cable.
6. Start the truck and log on.
7. Hold the sensor top against some metal (iron, steel, etc).
8. Make sure that the sensor has the correct status by checking the menu “Logged on service”:
9. The steering sensor must be active when metal comes within about 2 mm of the sensor top.
10. Reinstall the sensor as described in section 7.2.2.5.
…

---

INSTANT DOWNLOAD

---

Complete workshop & service manual with electrical wiring diagrams for Alexander Dennis Enviro 400 Busses. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Alexander Dennis Enviro 400 Busses (EURO3/EURO4/EURO4+) service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

MAKE: Alexander Dennis
MODEL: Enviro 400 (EURO3/EURO4&4+)
FORMAT: PDF

2291.pdf:
Enviro 400 (EURO 4&4+) 4 & 6 cylinder Service Manual
Date: July 2006 (03/08); 474 pages

2292.pdf:
Enviro 400 (EURO 3) Service Manual
Date: December 2005 (03/06); 450 pages

2297.pdf:
Enviro 400 (EURO 4&4+) Service Manual
Date: March 2006 (10/07); 466 pages

EXCERPT:
Air Suspension System Amended
“Description”
“The vehicle is fitted with air suspension, a function of this is the facility to kneel the vehicle at the front, or when fitted, an option to lower the suspension all round.”
“The air suspension is supplied from an auxiliary tank, sited on the right hand side of the chassis and forward of the battery carrier. Output supply passes through the system line filter, which filters the air before it enters the solenoid valve block and the levelling valves. Foreign matter in these items may cause them to malfunction.”
“Levelling valves are fitted to the front and rear axles of the vehicle. The levelling valves have a neutral or zero setting and at this position the vehicle ride height is set. Should the vehicle experience an increase in load, the chassis will move nearer to the ground resulting in the connection linkage pushing up and the valve spindle turning clockwise. This results in the valve allowing more air to be pumped into the air bags until the original ride height is achieved, although at a greater pressure. For a decrease in load the reverse happens, with the supply pressure shut off and the air bag pressure exhausting, the correct ride height is obtained.”
“For the kneeling system this function is controlled by a solenoid valve block and electrical relays via “”Raise”” and “”Kneel”” buttons in the drivers cab.”
“A proximity switch is fitted on the vehicle. The switch senses movement past a fixed indicator on the front axle. The indicator is sited at approximately half distance of its full travel. When the switch senses this indicator, the level warning light (yellow) will come on and the vehicle can be stopped at any point while the light is on. If the button is released before the light comes on the vehicle will return to a normal ride height.”
“Kneeling”
“When the kneel button is pressed valves 42 and 43 are energised. Valve 42 will be put in the open position and simultaneously valve 43 will close. The closing of valve 43 isolates the front levelling system and stops the levelling valve exhausting or inflating the air bags. Opening valve 42 allows the front air bags to exhaust, allowing the vehicle to kneel.”
…

---

INSTANT DOWNLOAD

---

Complete workshop & service manual with electrical wiring diagrams for Alexander Dennis Dart SLF Busses. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Alexander Dennis Dart SLF (Euro3/Euro4) service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

MAKE: Alexander Dennis
MODEL: Dart SLF (Euro3/Euro4)
FORMAT: PDF

2209.pdf:
Dart SLF Euro 3 Service Manual
Date: Nov 2001 (01/06); 378 pages

2302.pdf:
Dart SLF Euro 4 – 4 Cylinder Models Service Manual
Date: September 2006; 294 pages

2197.pdf:
Dart SLF Euro 3 – 4 Cylinder Parts Manual
Date: Nov 2001 (05/06); 280 pages

2225.pdf:
Dart 4 & 6 cylinder/ Pointer Operation Guide
Date: September 2003 (03/04); 72 pages

2266.pdf:
Dart 4 & 6 cylinder/ Pointer Operation Guide
Date: October 2003 (08/05); 72 pages

2300.pdf:
Dart E4 Pointer Handbook

2301.pdf:
Dart Euro 4 Parts Manual
Covering EURO 4 CHASSIS 4-CYLINDER MODELS: SFD1HFCR56GW1, SFD1HFCR56GW9, SFD2HFCR56GW9
Publication Number: 2301 Date: October 2006

EXCERPT:
Covering Euro 3 – 4 and 6 cylinder chassis models
SFD1BACR3*GWA
SFD1BACR3*GW1
SFD1B2CR3*GW1
SFD1BACR3*GW8
SFD1BACR4*GW1
SFD1CAFR3*GW1
SFD1C1DR3*GW1
SFD1C2CR3*GW1
SFD1C2DR3*GW1
SFD2BACR3*GWB
SFD2BACR3*GWC
SFD2BACR3*GW1
SFD2BACR3*GW8
SFD2BACR3*GW9
SFD2BACR4*GW1
SFD2BACR4*GWC
SFD2B2CR3*GW1
SFD2B2CR3*GW2
SFD2CACR3*GW1
SFD2CACR3*GW2
SFD2CACR3*GW1
SFD3CACR3*GW1
SFD3CACR3*GW8
SFD3CACR3*GW9
SFD3CACR4*GW1
SFD3CACR4*GW8
SFD3CACR4*GW8
SFD3C2BR3*GW1
SFD3C2CR3*GW1
SFD3E8ER3*GW5
SFD3FACR4*GWA
SFD4DBER3*GWD
SFD4DBER3*GW4
SFD4D6BR3*GW4
SFD4D6ER3*GW3
SFD4D6ER3*GW4
SFD4D8ER3*GW3
SFD4D8ER3*GW4
SFD4D9GR3*GW4
SFD4D9GR3*GW4
SFD5BACR4*GWA
SFD6BACR3*GWA
SFD6BACR3*GW1
SFD6BACR3*GW8
SFD6B2BR3*GW1
SFD6B2CR3*GW1
SFD6CACL3*GWA
SFD6C2CR3*GW1
SFD6B2CR3*GW6
SFD6CAFR3*GW1
SFD6BACR4*GWA
SFD6BACR4*GW8
SFD6CAFR4*GW1
SFD6BECR4*GW1
…

“Air Conditioning System – Clayton”
“Weekly checks”
“The Air Conditioning & Comfort Cooling System should be operated for at least ten (10) minutes to ensure compressor based lubricant is passed to key system components.”
“The compressor and belt should be checked for correct running/adequate belt tension throughout the operating speed of the engine.”
“After stopping and isolating the engine ignition, drive belts should be visually checked for good condition with pulley drive faces free from damage or dirt/grease build up.”
“Monthly checks”
“When Conditioning & Comfort Cooling Condensers are positioned at low level in the vehicle where they are susceptible to picking up dust and debris, the condenser complete surface should be subject to hose-pipe wash-out to clear all the rows and fins over the complete surface. (Note – steam cleaning or power wash on high setting should not be used due to risk of fin tube damage.)”
“Three Monthly checks”
“Any foam filters related to heater matrix/evaporators or fan protection should be removed and checked for dust/grease impregnation.”
“Any residue should be removed by washing the filter in warm detergent.”
“Compressed air should be used to blow into the relevant apertures as above with filters removed to displace any particulates present. (Eye protection should be worn during this operation)”
“Condensers mounted in the vehicle in other than low level position, should have compressed air applied to the entire finned surface to blow out any collected debris/dust such that fin apertures are clear. (Care should be taken to ensure that fins do not get damaged by compressed air pressure).”
“Mounting points for all condenser positions should be checked for tightness, and if hinged, the hinge mechanism lubricated.”
“Where hoses and end fittings are visible, they should be visually checked for abrasion or damage. If any visual signs are present, a recognized Gas Handling Trained Technician should be employed to de-gas and capture the refrigerant prior to the hose/fitting fracturing thus allowing gas to escape and vent to atmosphere. In the event of de- gassing other related components will be required to be changed.”
…

Pages from Massey-Ferguson Tractors MF7400 (7485-7490-7495 Dyna-VT) Operator Instruction Book

FILELIST:
AGCO / Sisu Power 4th Generation Engines (33, 44, 49, 66, 74, 84 and 98) Workshop Manual (9806-4100).pdf
Massey-Ferguson Combine MF7200 (CEREA 7274, CEREA 7278) Operator’s Manual.pdf
Massey-Ferguson Hydraulic Planter Spreader MF 104 – 106 L Operator Manual / Parts Catalog.pdf
Massey-Ferguson MF 9695/9795 CE Operator’s Manual.pdf
Massey-Ferguson Seeders Spreader MF 300 Operator Manual.pdf
Massey-Ferguson Tractors 6200 Series (6235-6245-6255-6260-6265-6270-6280-6290) Operator Instruction Book.pdf
Massey-Ferguson Tractors MF2400 (MF2430 STD-GE, MF2435 STD-GE, MF2440 STD-GE) Operation and Maintenance Manual.pdf
Massey-Ferguson Tractors MF6100 (6110, 6120, 6130, 6140, 6150, 6160, 6170, 6180, 6190) Operator Instruction Book.pdf
Massey-Ferguson Tractors MF7400 (7485/7490/7495 Dyna-VT) Operator Instruction Book.pdf
SisuDiesel 320, 420, 620, 634 Engines Workshop Manual.pdf
SisuDiesel 320, 420, 620, 634 Service Manual (8366 40634 (9806-4550)).pdf
SisuDiesel 645 Engines Workshop Manual.pdf
SisuDiesel Citius Series (44, 49, 66, 74 and 84) Engines Workshop Manual (8370 62637).pdf
SisuDiesel Fortius Series (33, 44, 66, 74 and 84) Engines Workshop Manual (8366 62500).pdf

EXCERPT:
CONTENTS
Chapter 1
TRACTOR IDENTIFICATION
Chapter 2
INTRODUCTION – SAFETY INSTRUCTIONS AND WARRANTY
Chapter 3
INSTRUMENTS AND CONTROLS
Chapter 4
OPERATION
Chapter 5
SERVICING AND ADJUSTMENTS
Chapter 6
SPECIFICATIONS
Chapter 7
ACCESSORIES AND OPTIONS
Appendix
CONVERSION TABLES
Index
…
5.3 – OPERATOR SERVICE GUIDE
5.3.1 – Engine, fuel and cooling systems
1. Check/clean the dry air filter elements (section 5.9).
2. Check the radiator coolant level (section 5.10).
3. Clean the main radiator and all other cooler element fins (section 5.10).
4. Check the level of smoke emission from the exhaust.
5.3.2 – Electrical circuit and instruments
5. Check the condition of the battery and the electrolyte level.
6. Check the tightness of the battery connections and battery safety.
5.3.3 – Front axle and steering
7. Check the oil level in the front axle and final drives (4WD).
8. Lubricate the drive shaft/universal joints (4WD) (section 5.6).
9. Lubricate the steering pivots/suspended front axle.
10. Check the steering and wheel alignment (including tyre wear and damage).
5.3.4 – Transmission and hydraulics
11. Check the transmission/hydraulics oil level.
12. Lubricate the trumpet housing bearings (section 5.6).
13. Check the oil in the rear final drive units (according to model).
14. Check the “ZUIDBERG” front PTO oil level.
5.3.5 – Clutch
15. Check the clutch fluid level.
5.3.6 – General
16. Check and top up the windscreen washer bottle (section 5.7).
17. Lubricate all points with grease or oil as specified in the Operator Instruction Book (section 5.6).
…